01-03-2013, 11:24 PM
01-06-2013, 04:41 PM
01-06-2013, 07:36 PM
I think that those mounts were some sort of rubber grommet propitiatory to Philco, sort of like those triangular chassis shock mounts on some sets, I don't know where anyone is making repros or no. The closest thing I can think of to those are maybe shock mounts for a small refrigeration compressor, or you can try some thick washers with the same size center hole. The only other answer would be to make a mold and cast some out of a D.I.Y rubber compound, if you can still get it.
Regards
Arran
Regards
Arran
01-06-2013, 08:47 PM
If you go to someplace like Graingers and look for rubber vibration isolators there is a pretty wide selection and perhaps something might be close enough or be adaptable to what you need: http://www.grainger.com/Grainger/cylindr...sst=subset . Renovated Radio also seems to have some rubber repro items though not these exactly but it might be worth an ask.. http://www.renovatedradios.com/parts.html
Bob
Bob
01-06-2013, 11:36 PM
Here is the rubber grommet selection form Grainger which may be worth looking through:
http://www.grainger.com/Grainger/rubber-...-c1x?xi=xi
Regards
Arran
http://www.grainger.com/Grainger/rubber-...-c1x?xi=xi
Regards
Arran
01-07-2013, 10:01 AM
Another option is to start with some laboratory rubber stoppers and adapt them http://www.amazon.com/Best-Sellers-Indus.../393458011
bob
bob
01-08-2013, 02:04 PM
Thanks for the suggestions. I think I found some items from renovated radios that will work. I needed to order some other stuff from them anyways
01-10-2013, 11:18 PM
01-10-2013, 11:35 PM
I've also been examining my speakers more closely and discovered that the Wheelers are not made very well and the cones don't have much spring left in them. So I pulled out the original Philcos for another look. After some careful scraping and compressed air blowing, I actually got the voice coils moving fairly well and decided to patch them up.
Yuck!
Making good progress
I used GC Service Cement and coffee filters to patch up the cones.
I figure if these actually work, I'll recone them properly. I think the radio will be happier with the original speakers back in it
Yuck!
Making good progress
I used GC Service Cement and coffee filters to patch up the cones.
I figure if these actually work, I'll recone them properly. I think the radio will be happier with the original speakers back in it
01-11-2013, 01:13 AM
Bob, nice that your putting back in the originals. A lot of work to clean them up but I think you will be happy. Looks like they are coming along well. Nice job.
Jerry
Jerry
01-12-2013, 03:03 PM
Looks good so far. Hope the iron windings are OK. Best take it slow on the cones.
01-17-2013, 05:14 PM
01-17-2013, 06:35 PM
Bob, I'm not certain what you used on those cans, but the came out absolutely lovely. Nice job. Are you going to keep your method secret?
Jerry
Jerry
01-17-2013, 06:54 PM
WOW! Yes, please share! I've never been able to obtain those results on the early 1930s Philcos...yet...
01-17-2013, 07:59 PM
Thanks! Your answer is right in the photo - Simichrome and a cotton cloth. I cut the cloth into a long strip about 3 inches wide, dabbed on a little Simchrome, wrapped it around the can, grabbed one end in either hand and buffed the cans like I was shining shoes. I used the same stuff on the copper caps.