What color for sides of a 3650
Posts: 371
Threads: 103
Joined: Jul 2011
City: Calgary, AB, CA
I have a Philco 3650 and the front has a very good finish , but the sides and top are very bad.. I am going to
redo the sides and top.. I already have those parts stripped and ready. Can anyone suggest a Mohawk toner that would be the same as the original color, or close to it?
Thanks ,,,,,,,,,, Dan in Calgary
Living in Calgary Alberta
Posts: 5,084
Threads: 270
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
Hi Dan, a photo of what you have might help. The Canadian 3650 could be similar to the American 650B table model or the 660X console. See http://www.philcoradio.com/world/images/canindex.pdf
As for the toners, I'll have to let someone else provide that advice.
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
As I recall, the Canadian 3650B's cabinet is identical to the USA 650B.
In which case...you want Mohawk Extra Dark Walnut Ultra Classic on the top, sides, and trim; Mohawk Medium Walnut Tone Finish on the front panel.
--
Ron Ramirez
Ferdinand IN
Posts: 371
Threads: 103
Joined: Jul 2011
City: Calgary, AB, CA
(05-14-2015, 06:56 PM)Ron Ramirez Wrote: As I recall, the Canadian 3650B's cabinet is identical to the USA 650B.
In which case...you want Mohawk Extra Dark Walnut Ultra Classic on the top, sides, and trim; Mohawk Medium Walnut Tone Finish on the front panel. Thanks Ron. A fast response.I have Extra Dark Walnut, but is it the same as the Extra Dark Walnut''Ultra classic''?
Living in Calgary Alberta
Posts: 5,084
Threads: 270
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
There are two types of Mohawk toner, dye based (ultra classic) and pigment based (Tone). Ultra Classic is the dye based and tends to show the wood grain more than the pigment based toner which is more opaque.
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
I've used Extra Dark Walnut in the Ultra Classic (dye) and the Tone Finish (pigment) versions, and I really can't tell much of a difference in these - both are so dark that they will quickly hide the grain of the wood.
--
Ron Ramirez
Ferdinand IN
Posts: 371
Threads: 103
Joined: Jul 2011
City: Calgary, AB, CA
(05-14-2015, 08:59 PM)Ron Ramirez Wrote: I've used Extra Dark Walnut in the Ultra Classic (dye) and the Tone Finish (pigment) versions, and I really can't tell much of a difference in these - both are so dark that they will quickly hide the grain of the wood.
Thanks for the information. I will use the Extra Dark Walnut. If it isn't what I want I can always remove it and use the classic
Living in Calgary Alberta
Posts: 4,703
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
I believe that the Extra Dark Walnut will be fine, the top and sides of most of the 1936 model tombstones are made out of single, molded, piece of laminated and grainless wood anyhow so there really isn't anything there to see. I think it's poplar but it could be any cheap white hardwood really, and the grain (such as it is) runs from back to front. As far as I can remember the Canadian built models use this same style of cabinet, though the front panel veneers may vary.
Regards
Arran
Users browsing this thread:
|
|
Recent Posts
|
|
12' Philco
|
| If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel.
Kareem would have an e...morzh — 01:48 PM |
|
12' Philco
|
| And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM |
|
Hickok AC51 tube tester
|
| I think they have only shown the secondaries of the transformer.
Two of them feed the rectifiers' filaments.morzh — 12:58 PM |
|
IF can wire size and Rubber mounts?
|
| Arran
If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM |
|
12' Philco
|
| Rod,
Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently.
H...morzh — 12:54 PM |
|
Hickok AC51 tube tester
|
| Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM |
|
IF can wire size and Rubber mounts?
|
| Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM |
|
Hickok AC51 tube tester
|
| Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM |
|
IF can wire size and Rubber mounts?
|
| A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM |
|
My last cabinet for this year
|
| Hello Dan,
That is really beautiful what great looking radio you have !
I have friends who live in Calgary and the wea...radiorich — 01:51 AM |
|
Who's Online
|
| There are currently no members online. |
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
