Posts: 765
Just finished this cabinet , I was a basket case got it last year at auction in Houston, 50 bucks
All though im having problems or should I say my electrical guys cannot get the oscillator to work. I know the basics on these tube radios thats it , I do all the easy stuff or grunt work as you call it. Dick gave up on it and now Mike is pulling his hair out to. I cant tell them what to do, me no nothing
He will figure it out or it will become a shelve queen
I threw in a bonus picture for Ron. Im still waiting on grill cloth for my 16b,s and Dick still has some work to do on one chassis, it,s sounds distorted and low on power and needs an alignment .
Attached Files
Image(s)
(This post was last modified: 06-07-2015, 10:10 PM by
Fred Taylor .)
Posts: 5,088
Posts: 765
Thanks, for the only reply on this radio.
I don't think Ron has seen this post yet, he normally puts his 2 cents worth in
(This post was last modified: 06-09-2015, 07:25 PM by
Fred Taylor .)
Posts: 13,776
Okay...you asked for my opinion...here it is:
Other than the decal, the cabinet is your normal beautiful work.
The decal, though...
That isn't a DCL-PH8, is it?
Posts: 765
I wasn't sure because the part # had been cut away on the decal sheet and it looked at the time it was the right one, I threw the dice and lost
Posts: 4,109
(06-09-2015, 07:34 PM) Fred Taylor Wrote:
Join the club Fred, lol
I was doing Mikes 66 and Ron said the same thing. I ended up stripping and redoing it since it was not my cabinet.
Kirk
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 15,819
He's alive, ladies and gentlemen, he's alive!
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 765
(06-10-2015, 06:08 PM) morzh Wrote:
Kirk was probably was bit buy a spider in that new work shed and took time off to recover
(This post was last modified: 06-12-2015, 12:35 PM by
Fred Taylor .)
Posts: 15,819
The spider though never recovered.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Users browsing this thread: 2 Guest(s)
Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone,
Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many.
Take care and BE HEALTHY! Gary
P.S. Can't get the right color you need? I ...GarySP
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire.
The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members,
Hope you can help me identify this type of wire in the photo I have attached. I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind.
Check any soldered, riveted ground conne...Chas — 01:24 PM
Who's Online
There are currently no members online.
All though im having problems or should I say my electrical guys cannot get the oscillator to work. I know the basics on these tube radios thats it , I do all the easy stuff or grunt work as you call it. Dick gave up on it and now Mike is pulling his hair out to. I cant tell them what to do, me no nothing 
He will figure it out or it will become a shelve queen 
I don't think Ron has seen this post yet, he normally puts his 2 cents worth in 
The decal, though... 
That isn't a DCL-PH8, is it?
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
