Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

pre war chairside/Finished/almost
#1

Heres another , a very nice GE chair side, the sound on this very nice , yes it plays but will go thru it for performance and safety. Very nice looking with those sliding doors and book matched veneer on top and phono cover slides and hides with the booked veneer . Slide rule dial, AM and 2 short wave bands, storage area in back for your albums or mags. Very nice pre war set Icon_eek Icon_eek Icon_eek


Attached Files Image(s)
               
#2

Up date on cabinet, grain filled and toned and cleared, will complete when electrical is done including turntable, this radio has a light on bottom front of cabinet which is pretty cool. The bulb , socket and wiring is there but no lens. I call those cat eyes, like the reflector nuts for old bicycle license plates. The hole is there ,its 3/4 hole for cat eye, if any of you have one to sell let me know. It suppose to come on when set is turned on, theres a name for that light , I don't know what it is. May be to let you now the power is on? 


Attached Files Image(s)
               
#3

Ok got this far and this does not look like the same radio 2 weeks ago, the sound is amazing coming from this 7 tube radio, 12 inch speaker Icon_eek Someone will be happy when they purchase this because I have no more room to keep any radios, I do have more room but I will not allow my self to do so, I have seen hoarder shows and do not want to get anything near that. Icon_clap


Attached Files Image(s)
                   
#4

A few more Icon_eek Icon_eek Icon_eek


Attached Files Image(s)
           
#5

Very nice. How did you deal with the roll top doors?

Charlie in San Antonio
#6

(07-23-2015, 06:02 PM)ccomer1955 Wrote:  Very nice. How did you deal with the roll top doors?

I left the doors on, cleaned and used spray toner by mowhawk.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM
Philco 38-7 Speaker
7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM
40-150 General questions
I discovered a stamp on the underside of the breadboard on my Philco 40-150. It is"56-1417' in black ink with numbe...Kevin_D — 07:14 AM
Philco 38-7 Speaker
FYI the Impedance of the HR20 (the one I have) secondary of the audio transformer is 5 ohms. The 38-7XX speaker is suppo...tludka — 04:22 PM
Philco 38-7 Speaker
Yeah, don't use the transformer currently on the H-20 (Dopf, I thought "H20, is that new technology, a speaker usin...MrFixr55 — 03:51 PM

[-]
Who's Online
There are currently 2776 online users. [Complete List]
» 2 Member(s) | 2774 Guest(s)
AvatarAvatar

>