Posts: 4
Threads: 1
Joined: Jan 2016
City: Jackson NJ USA
Hi All,
New member- first time poster.
I have a model 81 that I have rebuilt. Replaced all caps, resistors and rewound the ant coil (primary side).
The speaker cone is in bad shape but it plays.
The set is working and I can get a local station in my basement- so I am not too far from finished.
I have been making voltage measurements on the tubes to confirm everything is in spec and I am having a problem reconciling the 42 output tube with the rider voltage chart for this radio. Specifically, the control grid CG to cathode K. The rider manual calls for 2.3 V. The 42 tube data sheet calls for a control grid voltage of -16.5 to -20 v. I am measuring about -17 v from CG to K (ground). Not sure if I have a problem or not.
My plate, screen and filament voltages are in spec. (riders chart).
thanks for the help,
Anthony
Posts: 670
Threads: 11
Joined: Sep 2014
City: Bellmawr, NJ
I say ,,,you are in the range between -16.5 to -20,,,sounds good to me
Posts: 5,129
Threads: 271
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
Welcome to the Phorum!
If its playing well the voltage reading seems good to me. An alignment might be helpful as well.
Posts: 4,410
Threads: 416
Joined: Jun 2011
City: Boston
State, Province, Country: Massachusetts
Anthony, you live in the same town as one of our members, Morzh! Good luck and welcome to the land of Philco.
paul
Tubetalk1
Posts: 16,285
Threads: 567
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Tony
Where in Jackson are you?
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 4,818
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
Perhaps it was an error? The control grid voltage should never be positive on any audio output tube that I know of, maybe it was supposed to be -23 volts rather then 2.3 volts? If it was actually 2.3 volts the output would sound like garbage if it worked at all.
Regards
Arran
Posts: 4
Threads: 1
Joined: Jan 2016
City: Jackson NJ USA
(01-20-2016, 10:56 PM)morzh Wrote: Tony
Where in Jackson are you?
Hi Morzh,
I am on Autumn Avenue, between Diamond and Cobain roads. About 3 minutes from the Justice complex.
Posts: 4
Threads: 1
Joined: Jan 2016
City: Jackson NJ USA
Thanks for the help!
It does need an alignment (IF and the dial). Unfortunetly, the dial is brittle and in alot of little pieces. I ordered a replica replacement. When that comes in I should be able to do the dial and other alignments.
Yes, I'm in Jackson- near diamond road about 3 minutes form the Justice complex.
Also, I used to attend the NJARC meetings in Freehold with my grandfather until they moved to Princeton and Wall.
thanks again,
Anthony
Posts: 16,285
Threads: 567
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Not too far, 6 minutes maybe. I am in a development by St Aloisius church, on Bennets Mills.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 4
Threads: 1
Joined: Jan 2016
City: Jackson NJ USA
(01-21-2016, 08:46 PM)morzh Wrote: Not too far, 6 minutes maybe. I am in a development by St Aloisius church, on Bennets Mills.
Yes, I know that area. My Kids went to St. Al's.
-Anthony
Users browsing this thread: 2 Guest(s)
|
|
Recent Posts
|
|
An attempt to remove the Field Coil from a G speaker
|
| So,
Q1. Does anyone know where to get the spider.
Q2. If there is no such place, what material is best? I doubt tin...morzh — 09:43 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Arran
The oxidation seems to go deep, a few layers. The break starts right there, but then it will occur on every la...morzh — 07:35 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Mike,
This is just a thought, the are on the coil where the verdigris (green oxidation is) I wonder if that is where ...Arran — 06:32 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Mike;
I've made a one or two spiders by using some card stock, and a razor blade, it took more then one try but they ...Arran — 05:48 PM |
|
Philco 91 Restore Code ??
|
| I wondered about that. Wish there was some place local to get this stuff.dconant — 04:20 PM |
|
Philco 89 indicator light.
|
| Bending the lamp bracket (moving the lamp, that is) can possibly change the shape of the pointer a bit, but not its loca...morzh — 04:01 PM |
|
Philco 91 Restore Code ??
|
| Because the usable power rating of it then is (3,200/20,000)*25W= 4W.
Maybe a tad more due to the mass, but not much. Yo...morzh — 03:59 PM |
|
Philco 89 indicator light.
|
| Thank you Dan, that was the trick. I kept trying to rebend the lamp bracket but that wasn't doing anything to help.Jim Dutridge — 02:18 PM |
|
Philco 91 Restore Code ??
|
| 20K 25 watt. I thought it was a 20 watt at first.dconant — 01:37 PM |
|
My Philco 37-116 Restore
|
| Nah, too much and not that important.morzh — 01:33 PM |
|
Who's Online
|
There are currently 4197 online users. [Complete List]
» 2 Member(s) | 4195 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
