Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Value of a Philco 41-287
#1

Yesterday, at a local thrift store I found a Philco 41-287 ? Not able to see the actual nameplate. The price was $90.00
Case was ok, grill cloth torn.  Is this a fare price? Icon_crazy
 
#2

Welcome to the Phorum!
Icon_wave

Here's a pic of a 41-287x, is this what you found?

As to value, it depends entirely on whether its worth $90 to you. Others may have a different opinion but if the chassis is in good shape, ie. not a lot of rust and looks clean, and all the tubes are there it may be an OK price. You can always offer them less and work your way up. Keep in mind that unless its been electronically restored you will need to have that done before playing it.
#3

Thank you the picture is positively the radio in question. I will have to convince my better half that there is room for this one if I can haggle the price down. The chassis looked rust free and tubes appear to be all there. Hopefully they will be able to move it out from where it is now. ( They are remodeling the store, big mess. )
Once again thank you!
#4

 One thing to keep in mind with many of these 1941 models is that they used a Tenite plastic escutcheon, pushbuttons, and knobs that are often warped, shrunken, or otherwise disintegrating, and you will be looking at another $60+ to replace those with reproductions. Then you have the rubber/gutta percha covered wiring which is usually shot, and last but not least an open primary on the output transformer. This is assuming that the cabinet is in good shape and does not require any refinishing or repair work. So no, $90 is too much money in my opinion, I would try to pay as little as possible for it, maybe no more then $40 $50 if you really like it, preferably less.
Regards
Arran




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM
Philco 38-7 Speaker
7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM
40-150 General questions
I discovered a stamp on the underside of the breadboard on my Philco 40-150. It is"56-1417' in black ink with numbe...Kevin_D — 07:14 AM
Philco 38-7 Speaker
FYI the Impedance of the HR20 (the one I have) secondary of the audio transformer is 5 ohms. The 38-7XX speaker is suppo...tludka — 04:22 PM
Philco 38-7 Speaker
Yeah, don't use the transformer currently on the H-20 (Dopf, I thought "H20, is that new technology, a speaker usin...MrFixr55 — 03:51 PM

[-]
Who's Online
There are currently 2371 online users. [Complete List]
» 1 Member(s) | 2370 Guest(s)
Avatar

>