1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 38-5 Restoration Advice
Tgace459
Member
***
Posts: 130
Threads: 25
Joined: Apr 2016
City: Buffalo NY
#1

07-23-2017, 08:06 PM
I just had a guy drop off this beautiful 38-5. Probably one of the cleanest chassis I've seen yet (the photo is after a light scrub and wipedown) and it has something I've never seen before...it's original cardboard back.

[Image: http://i.imgur.com/eSdmMeJ.jpg]

[Image: http://i.imgur.com/4cnz8KD.jpg]

[Image: http://i.imgur.com/bT09zNM.jpg]

The cabinet is in great shape except for some topcoat crackle, the typical scuffing at the base and this ONE blemish.

[Image: http://i.imgur.com/2bmiHGa.jpg]

I'd like to preserve the original finish with some topcoats of fresh lacquer, but was looking for some advice on how I can better conceal that blemish. It looks like someone used some sort of epoxy (?) to fill a chipout. I was contemplating some sanding and topcoating, but I don't want to make it any more obvious than it already is. I've been burned "chasing problems" around before where I create a problem while trying to fix another.
(This post was last modified: 07-23-2017, 10:19 PM by Tgace459.)
Find
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#2

07-23-2017, 08:24 PM
Great looking radio!!
If it were mine...I'd probably leave it alone, but then I tend to buy radios that are in bad shape so that no matter what I do they are better off than when I get them Icon_lol
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
Kenneth F. Besso Jr.
Senior Member
****
Posts: 667
Threads: 11
Joined: Sep 2014
City: Bellmawr, NJ
#3

07-23-2017, 08:38 PM
the card board back,,,is the money maker,,,,,
Find
Tgace459
Member
***
Posts: 130
Threads: 25
Joined: Apr 2016
City: Buffalo NY
#4

07-23-2017, 08:45 PM
Any suggestions on how I can preserve that back? Are there any sorts of sprays or laminates that can stiffen and protect it? Maybe some clear epoxy spray?
(This post was last modified: 07-23-2017, 08:56 PM by Tgace459.)
Find
sam
Phorum Expert
*****
Posts: 2,572
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
#5

07-23-2017, 08:54 PM
would imagine clear coating it .
but I don`t think it would make it shinny as it would soak in

sam
Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 310
Joined: Nov 2013
City: Kings Park NY
#6

07-23-2017, 09:00 PM
I see nothing....


Attached Files Image(s)
   
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
Tgace459
Member
***
Posts: 130
Threads: 25
Joined: Apr 2016
City: Buffalo NY
#7

07-23-2017, 09:15 PM
(07-23-2017, 09:00 PM)OldRestorer Wrote:  I see nothing....

Might be your browser.....
Find
sam
Phorum Expert
*****
Posts: 2,572
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
#8

07-23-2017, 10:03 PM
tgace
all your pic`s are gone  

sam
Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#9

07-23-2017, 10:11 PM
It isn't Kirk's browser, I do not see any of your pictures either.
--
Ron Ramirez
Ferdinand IN
Find
Tgace459
Member
***
Posts: 130
Threads: 25
Joined: Apr 2016
City: Buffalo NY
#10

07-23-2017, 10:14 PM
How about now?
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#11

07-23-2017, 10:18 PM
Yes, thank you.
--
Ron Ramirez
Ferdinand IN
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone,  Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration