Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco hippo/ Canadian
#1

Hello,
New to the forum and I hope this is in the right place. I have a Canadian Hippo I would like to restore and have a few issues. First it has no chassis ink stamp on it. It does have a metal plate rivited to it that says chassis 75. It hasn't no rf coil by the gang on top of chassis. Antenna screw  
Has an insulator on it. Main cap has been replaced with a 3 way cap but two are wired in parallel. So it has a 120uf and a 20 uf for the power which is wrong from my research. The tube line up is 14AF7, 2-7B7, 1-35Z5, And a  50l6gt , would anybody have a exact diagram or know where i can get one. I'm off This week and want to get her up it sort of looks like a 48-460 type 122 but it's not. Any help would be much appreciated 

Regards
#2

Welcome to the Phorum!
Icon_wave

The Canadian 75 model is similar to the 48-460 according the the listing that Ron (the Phorum founder) has here: http://www.philcoradio.com/images/phorum/canindex.pdf

You may be able to get the exact Canadian schematic from Just Radios at http://www.justradios.com/schematics.html
#3

Hey! Thanks for the quick reply! Yes I saw that, but that came in a couple different chassis huh? It looks like tube lineup was different on several models, the antenna, rf coil not on top, and power caps. I just haven't been able to find a " just chassis 75 " schematic. I just want to talk to someone to make sure it's the right schematic. Not trying to be anal, but I've already paid once for a schematic I was promised was the right one and was not. It was not from just radios though. This will go In my blooming collection and I just want the correct schematic to make sure some older work done on it was correct and not some hack job. Just seeing the power cap issue, which is easily overcome, I'm worried there may be something I may not see that bites me. I like to have everything I need when I start a restore, but then again on old stuff sometimes that's not possible, you just have to dive in. And I'm willing to pay again if I know it's the correct one. I've shot just radios an email and what I've read they are a great company to deal with. But if anybody has any pointers, history, known issues or clean schematics  on the model I'm all ears!
#4

Kinda odd tube lineup. Would think it should have a 7C6 near the 50L6 not a 2nd 7B7. Does it have sticker inside to check tube arrangement??

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#5

(12-31-2017, 12:22 AM)Radioroslyn Wrote:  Kinda odd tube lineup. Would think it should have a 7C6 near the 50L6 not a 2nd 7B7. Does it have sticker inside to check tube arrangement??

Yes it is from what I researched. The tube layout diagram is not on the bottom. I don't even see old glue marks where it would have been stuck. There is one paper tag on the inside right of cabinet. I'll post pic here.


Attached Files Image(s)
   




Users browsing this thread:
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently no members online.

>