Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Why is it always the right side?
#1

Today while checking out a Zenith Allegro stereo for someone, a very good question came to mind after the right channel basically died on me. Why is it always the right side that gives out on vintage, solid state stereos? I tinkered around with a few 70's stereos in the late 90's and this was already an issue then. Either dead or weak on one side. Now that I've been tinkering with solid state again, I've once again found they often go bad on the right channel. Why is this? I have actually seen Magnavox Astro-Sonic consoles that are either weak or dead on the right side, yet they play on for years in garages and stores on the left side. Either this is an oddity caused by how solid state electronics are set up or Ohio has an odd effect on electronics! Icon_confused

No matter where you go, there you are.
#2

That's not anything I encountered servicing.

Must be living in the Twilight Zone?  Yikes

Tom
#3

Well, the issue with the Zenith Allegro appears to be the vintage speakers we tried out on it. They might have tested good with the meter, but something went wrong and I think that is why the right channel conked out on the Zenith. Same speakers also caused my Realistic stereo to act strange and I think they have a date with the sledge hammer later on. Icon_sad

No matter where you go, there you are.
#4

I would guess that the volume/balance pots probably have a lot to do with it, unless you are speaking of playing records in which case the cartridges can and do get messed up.
Regards
Arran
#5

Yes, Deoxit on balance controls and volume and balance controls often fixes it. A leas it's the first step.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM

[-]
Who's Online
There are currently no members online.

>