Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

FADA 195 A
#1

As some may know the New England Vintage Electronics Club had our meet today in New Hampshire, though the morning looked promising a very pretty Sunrise the day was cool and overcast for the meet. Despite that many tailgated their wares and we had good crowds in the hall and in the Parking lot tailgating area. I think the tailgating is getting more popular due to not having to haul your goods all the way from lot to the hall just set up by your car, van, etc..... A high light was when of our members flew over several times in a Helicopter quite low at times to film the overhead view of the event, perhaps I can post when available.  Icon_smile

At the meet a senior club member and a true gentleman in the hobby approached me with a FADA 195 A from the early 20's? Asking my help in locating a schematic, I have looked on line but no luck. We did meet another fellow a NJARC member who had worked on that set some time ago and offered some pointers, but also said he could not find a schematic.  Icon_confused

So to these in this esteemed group, can any one render some assistance? 

I am much obliged. 

Paul

Tubetalk1
#2

cant help here  have lot of fada schematic's  but nothing on 195a

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#3

Thanks Sam, it is an oldie, way back machine. 

Paul

Tubetalk1
#4

Paul;
  I have a Fada 175A, and I could not find a factory diagram for it either, but I found one that someone had made by tracing out the wiring in the set, in my case it was a 1924 model. One way you can often tell is that 1924-25 and earlier sets will have UV bayonet style sockets, but the 1925-26 and newer models will have UX style four pin style.
 The 192A was also known as the "Neutrolette", which I think was intended to be an economy model, unlike the Fada 175A there is a diagram in either the first Riders volume, or in one of the Gernsback books, it's a 1925 model. Five will get you ten that one or both of the audio interstage transformers are open circuit, my 175A still has the originals, one is good but the other is open circuit on one winding. Here is a site that has some of Gernsback;s books posted, as well as lots of early radio books and magazines, if you want to look:

https://www.americanradiohistory.com/

Regards
Arran
#5

arran
here is a copy of 175  same as 185

https://documentcloud.adobe.com/link/tra...f428ea762b

lol ok so it copied whole section  175  is  13-10

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#6

Sam;
  Those are at least a decade newer, my 175A is a three dial TRF from 1924, it's from the original F.A.D.Andrea company, before Frank sold the company.
Regards
Arran




Users browsing this thread:
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently 2318 online users. [Complete List]
» 1 Member(s) | 2317 Guest(s)
Avatar

>