1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
37-10 volume control
PencilmanCA73
Junior Member
**
Posts: 3
Threads: 1
Joined: Jul 2018
City: Olympia State, Province, Country: Washington
#1

12-03-2018, 10:50 PM
I am working on a Philco model 37-10 that has a bad volume control, part number 33-5158. I am having trouble tracking a replacement down. Any help finding one will be appreciated. I had a link to a site that had an awesome selection of controls but I lost that link when I was saving it to my bookmarks.
Find
klondike98
Phorum Moderator
******
Posts: 5,084
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#2

12-03-2018, 10:58 PM
Welcome to the Phourm!
Icon_wave

If you don't find a replacement, good option is to contact Mark Oppat and he can probably fix it or will have something for you.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#3

12-03-2018, 11:41 PM
Welcome!
Mark O more than likely can build a pot for you. I just got a similar one for my 116B it was abt $25.

GL
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
PencilmanCA73
Junior Member
**
Posts: 3
Threads: 1
Joined: Jul 2018
City: Olympia State, Province, Country: Washington
#4

12-03-2018, 11:57 PM
Hi, Bob thanks for the welcome to the Phorum.

I will check Mark Oppat and see what he can do. The site I mentioned has an enormous selection of controls and models and includes a list of substitutes. I am doing this repair for my daughter. I am a retired electronics guy and it's been a while since I have done any work of this nature so I have been scrambling to find all of the equipment I need to do the job. Most parts have not been a problem.

I checked your restoration page, nice work.

Jim
Find
PencilmanCA73
Junior Member
**
Posts: 3
Threads: 1
Joined: Jul 2018
City: Olympia State, Province, Country: Washington
#5

12-04-2018, 12:00 AM
Thanks, Terry, I will check Mark Oppat.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration