1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 38-4 question
emcjim
Junior Member
**
Posts: 9
Threads: 3
Joined: Apr 2018
City: Kenosha, WI
#1

12-30-2018, 11:46 AM
Hello,
    working on a 38-4 chassis and there is a resistor connected to C25 that is not listed on the component diagram ( I have attached that as well as a picture of the chassis). It looks pretty burnt and I want to replace it but want to be sure of the value. After looking at the schematic I am thinking that it is listed on the parts list as 27X, 1000 ohm 1/2 watt resistor, where on the 38-5 would be the shadow meter instead. Can anyone let me know what this is? Thanks.
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

12-30-2018, 02:08 PM
Yes it looks to be the 1K resistor via the diagram. It supplies the plate voltage to the rf amp and mixer tubes. More than likely #10 or 25 was leaky and caused excessive current flow thru the resistor.

GL
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
emcjim
Junior Member
**
Posts: 9
Threads: 3
Joined: Apr 2018
City: Kenosha, WI
#3

12-31-2018, 10:44 AM
Thank you for the info, much appreciated
Find
« Next Oldest | Next Newest »




Users browsing this thread:
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5503 online users. [Complete List]
» 4 Member(s) | 5499 Guest(s)
AvatarAvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration