Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

I picked up this Opus 6 yesterday
#1

Talk about a sweet sounding radio.  Wow this thing sounds good. Superb reception as well.  Best I've had at my place where many of my other radios have trouble The cabinet is in excellent condition as are the glass knobs and buttons. 6 speakers, all working.  I've been on the hunt for a nice one for a long time. My search is done.


Attached Files Image(s)
       
#2

Them Germans built nice ones in 50s, yes. Any Telefunken is an excellent radio.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

Just found one of these, will start restoring it soon. It is very nice condition but would like to recap it.

Jim
Spring Lake MI
#4

Jim please take lots of pics to share. David
#5

Will do.

Jim
Spring Lake MI
#6

At the very least I would want to replace the audio coupling capacitors, the tone correction cap on the primary of the output transformer (if it can one) and any bypass that runs between B+ and ground. A lot of West German radios used ERO brand capacitors, they are to German sets what Hunts are to British ones, replace on sight.
Regards
Arran
#7

Thank you Arran.
When I get started on this I will start a new thread.

Jim
Spring Lake MI
#8

Yes, my Grundig used ERO.....the worst I've seen so far. I keep them just so I could demonstrate how bad cap could drift. Up to 4 times up.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#9

Some tube-type and early solid-state Fishers also use ERO caps. The consensus seems to be divided on these as to replace vs. keep.

I replace them.

--
Ron Ramirez
Ferdinand IN
#10

Ron

when a cap goes up in value 4 times, to me there is no valid justification for leaving it in.
Out of all ERO caps in my radio (about 30+) there is no one single cap that did not go up at least 3x the value.
I think I might've even put a picture in my Grundig thread.
For comparison, all American caps in Philcos or Zeniths were 1.5x to 2x the value and in fact did work. Still needed to be replaced.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#11

No argument from me. Like I said...I replace them.

--
Ron Ramirez
Ferdinand IN
#12

https://philcoradio.com/phorum/showthrea...606&page=2

Actually, on this page I have the picture of 0.033uF cap measuring exactly 0.33uF.

Times 10.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#13

I was addressing the original poster in this, the set might work now, but it may not work a week from now, but replacing the audio coupling caps is the bare minimum someone should do.
Regards
Arran




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Gilfillan Brothers Car Radio?
There is a Mission Bell model 19/19A that could be what you’re looking for, Riders vol 4. It has the tube line-up of: 0Z...Joe Rossi — 05:01 PM
Looking for verification of correct schematic.
Definitely 870044RossH — 01:12 PM
12' Philco
Wonder if the chassis was big too.daveone23 — 12:38 PM
Philco 38-2 Automatic Tuning
Hi Ron, I have sent Radio Daze my concerns with the dial so I guess we will see. They used my original to make the repro...dconant — 12:27 PM
Hickok AC51 tube tester
How does the  5W4 and 83 tube filaments get fed?martinj — 12:25 PM
462ron
Hi Dan, your original dial appears to be lighter, easier to allow light through. My original is similar except it’s crac...462ron — 12:07 PM
Philco 38-2 Automatic Tuning
I received my new 38-2 dial. I'm a little disappointed. As you can see in the picture the blues have a white shadow. The...dconant — 11:13 AM
Philco 38-2 Low Volume
I have been playing my 38-2 for a while now and it is doing very well. I did have to replace the 6A8 (osc) as it develop...dconant — 11:03 AM
Philco Speaker Spider
Hello, Does anyone with a 3 D printer make the spiders for those old Philco speakers? That might be a good idea for some...dconant — 09:41 AM
Philco 16B Parts
Hello, I'm looking to buy a 16B but I'm not so sure of what I am looking at. First as seen from the picture it looks lik...dconant — 09:17 AM

[-]
Who's Online
There are currently 2766 online users. [Complete List]
» 1 Member(s) | 2765 Guest(s)
Avatar

>