Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 37-610
#1

Hi,

Some time ago a relative found me a Philco bullet model 37-610 at a sale. Upon inspecting it later, I noted that it did not have the Deco inlaid lines on the front:- http://www.tuberadioland.com/philco-37-6...mainl.html

It's also missing its dial glass and part of the knob, though I do have these parts that I've found since.

I've seen very few of these without the lines & have been uncertain as to their authenticity. Now one has shown up on Ebay:-
http://cgi.ebay.com/6596526279

Is there a story here somewhere regarding this as a variation?

Paul
#2

Looked at the ebay set. It's glaringly a strip 'n slobber refinish. I don't believe that these models ever had Di-Noc (printed grain) finishes, but we have to wonder if the black stripes may have been printed on the panels. I'll have to check on mine, but I've always thought that the black stripes were inlays. I have both the '36 and the '37 sets.

Another possibility is that on early cabinets, the stripes WERE inlays, and they might have done a run of cabinets with either printed stripes or none at all. Since the original finish is gone from this cabinet, that information is lost.
#3

I think I would have to agree with Doug here. Although that decal looks as if it might be original, the bottom trim should be toned a much darker brown; and it isn't on this set.

Some years ago, someone was selling a very good reproduction of the 1932-36 PHILCO decal. I once had a few of those, and they looked just like the originals, unlike what you can get today. The decal on this set could be one of those repros, placed on an older, poor refinish, for all we know.

I looked in my copy of Furniture History, and it is silent on the stripes/no stripes issue. It only mentions that the 1937 version was available in maple as well as walnut; the vast majority (28,100) were walnut as opposed to 3,000 in maple.

I wouldn't be a bit surprised if Doug is right on the money regarding the stripes being printed later on, although I seem to recall the 1936 model did have inlaid stripes?

--
Ron Ramirez
Ferdinand IN




Users browsing this thread:
[-]
Recent Posts
Zenith H725
Hello Ed, yes, I like letting projects run for few days to make sure they don't start acting up . Sincerely Richardradiorich — 01:03 PM
Philco 46-480 Electronic Restoration
I am almost finished with this restoration. All which remains is the power transformer. I cleaned it up some time ago, b...jrblasde — 12:41 PM
Philco model #20
I seem to recall in some TRF sets there being a Local/Distance toggle switch that removes the B+ from the first 24 rf tu...RodB — 09:46 AM
Refinishing Ideas
Hi Doppelganger, After rereading your thread, did you mount the Zenith speakers in the two bottom left and right pos...MrFixr55 — 09:39 AM
Philco model #20
Hi Rick, One other thing regarding volume on this set.  Make sure that the tube shield is in place.  this is that la...MrFixr55 — 08:22 AM
Philco model #20
Hi Rick, The volume control on the Model 20 has 2 sections and does 2 seperate things: One part of the control, ...MrFixr55 — 10:30 PM
Philco model #20
Hello again fellows , well I powered up the set this evening after I had changed every cap and resistor in this set and ...onlyrick — 09:34 PM
Zenith H725
Yes - better it happened on the repair bench than returning to the owner. The other question is - do I also dissect a...EdHolland — 09:08 PM
Zenith H725
That's a bummer but get them now. Paul BPaul Philco322 — 08:27 PM
Zenith H725
I completed the insulation on the cabinet interior (Al foil and hi temp silicone rubber), and reglued the speaker gasket...EdHolland — 06:18 PM

[-]
Who's Online
There are currently 798 online users. [Complete List]
» 1 Member(s) | 797 Guest(s)
Avatar

>