Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Rogers 10-85 cabinet all done
#1

I like these Rogers radios,especially some of the cabinets.
 I picked this one up last fall and during the winter I did the chassis,
and replaced the top veneer.
 Now I finally got the cabinet done.
 Dan in Calgary


Attached Files Image(s)
                   

   Living in Calgary Alberta
#2

Dan,
It looks great! Probably better in person.
Henry
#3

Do you have the signal strength indicator working? It is an interesting circuit.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#4

I suppose I am like a lot of other guys on these forums. I have not have any training in radio repair , or electronics.
So I don't understand a whole lot of the in and outs of how everything works. So to answer your question,
I did not know that the radio had a signal strength indicator. Sorry about that.

I guess I just replace the caps,check the tubes,and resistors ,clean the pots, and align the radio.
When it works OK after that I basically leave it alone.
It is my hobby , and I do enjoy it , but I am learning more about radios every day, and I hope it keeps me young.
I did enjoy looking at your site very much
Thanks
Dan in Calgary

   Living in Calgary Alberta
#5

There is a small light bulb in the dial scale that is tied to a grid on one of the IF tubes. As the signal changes, this bulb glows brighter. The reason that I asked is because it is hard to find a suitable bulb. I used one of the very small "grain of wheat" bulbs.  - - going from memory - - It is easy to miss this function altogether.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#6

Now I unde5stand what you mean by a ''signal strength indicator''

 I guess I just call it a tuning light,   On my Rogers 10-12 There are two of them, and on my Rogers 6R932 there is one in the very center if the cabinet.
   I also have one in my DeForest Crosley 'Buckingham, and some of the tombstone models have them also.
 
 It took me quite a while to find the right bulb,but once I did  I ordered 20 of them, because I am always running into Rogers radios.
  The biggest thing about the bulbs,   [I found ] was the amps had to be just right
  The bulbs that do the job are   #1448.
 Dan in Calagary

   Living in Calgary Alberta
#7

The tuning light indicator works good on this one, and I finally got it all back together.
   Dan in Calgary


Attached Files Image(s)
               

   Living in Calgary Alberta




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM
12' Philco
Not anymore Mike. Andre The Giant Born: May 19, 1946, Coulommiers, France Died: Jan 28, 1993 (46 years), Paris, Fran...RodB — 11:53 PM
IF can wire size and Rubber mounts?
Renovated Radios do carry what you need. As for the voltage, a wire should be at least 300V-rated.morzh — 11:13 PM
12' Philco
Andre the Giant got 2" on Kareem :lol:morzh — 11:11 PM
IF can wire size and Rubber mounts?
Thanks for the info but I doubt that a hardware store would be carrying the proper tuner assembly support mountings for ...georgetownjohn — 10:38 PM
12' Philco
Perhaps Kareem Abdul Jabbar?GarySP — 10:33 PM
My last cabinet for this year
Outstanding work, Dan! Take care and BE HEALTHY! GaryGarySP — 10:31 PM
My last cabinet for this year
They are a nice looking radio, Stromberg. I have a small tabletop octagon-dial one. It sounds surprisingly nice. And t...morzh — 09:40 PM
Philco 41-608 changer coupler
Different years but the same idea.morzh — 09:38 PM
My last cabinet for this year
That’s a beauty! :thumbup:klondike98 — 09:24 PM

[-]
Who's Online
There are currently 6536 online users. [Complete List]
» 1 Member(s) | 6535 Guest(s)
Avatar

>