1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 42-1008 122 Phono Transformer
Micro9
Junior Member
**
Posts: 36
Threads: 15
Joined: Aug 2007
City: Glendale,AZ
#1

11-24-2020, 04:01 PM
The radio has been completely restored...All caps replaced and resistors that were out of tolerance.Radio plays well on Am
and shortwave with good fidelity.When I try to play MP3 or bluetooth thru the rca plug on the xformer,It sounds real tinny with very little bass.
Is there a problem with the transformer or is the phono xformer not able to have good bass response thru it?
Before I send the BOL off to Westek for rebuild I would like to know if that xformer is good.
Here is a link to the schematic from Nostalgia Air:  http://www.nostalgiaair.org/pagesbymodel...013487.pdf
The part number is:32-8196 for the xformer..The pri reads 103 ohms and the sec reads 1596ohms....RCA input reads around 10 ohms..
TKS in advance...
Find
jphouchins
New Member
*
Posts: 1
Threads: 0
Joined: Aug 2020
City: White Bear Lake State, Province, Country: MN
#2

01-17-2021, 06:36 PM
Those values for your transformer are correct. Good luck with your BOL. I have restored three of them and it is always satisfying to get them to work properly.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM

[-]
Who's Online
There are currently 2817 online users. [Complete List]
» 2 Member(s) | 2815 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration