Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco Tropic 103 valve radio made in England
#1

Had this Philco Tropic 103 come my way can find little about it i guess its a export model for the Commonwealth 
Valves EM81/ECH81/EBF89/EBC81/EZ80/EL84
 
WAVEBANDS 19M/25M/31M/SW1/SW2/BC


I believe its similar to the model UK 135

can find little around the web and no circuits for either of these 2 models


Attached Files Image(s)
                               
#2

I did find this but it's a bit hard to read.  https://www.todocoleccion.net/radios-ant...~x39757856 Seem that it's the same as the 101 model.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

Radio Museum has this but doesn't seem to have a schematic:
https://www.radiomuseum.org/r/philco_tro....html#data
#4

I have a copy of the UK Vintage Radio service data DVD, and Model 103 is not in there (neither is model 101).

I used to have one of those sets. I would guess very few made their way over here to the USA. It was likely made for export to Africa and possibly South America.

--
Ron Ramirez
Ferdinand IN
#5

Thank Folks parts list will be useful sadly the circuit not so clear but much better than none at all
#6

Very attractive set !!

I find it interesting that although it is made in the U.K. the connections on the back say "antenna / ground" instead of "aerial / earth". I wonder when the U.K. producers started using those terms?
#7

.... and .... having read the radio specifications from the link above (for the 101), it only has two SW bands, but three "bandspread" dials .... not often we see "band spread" on consumer sets. GE made one in the fifties, (X371/CX371) a huge table top set with a half-round dial and two chassis'. This Philco looks to be a nice compact set by comparison.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM

[-]
Who's Online
There are currently no members online.

>