1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Vintage Hi-Fi, Stereo and Audio
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
M3850T Philco / Ford
dannyb
New Member
*
Posts: 2
Threads: 1
Joined: Jul 2022
City: Martinez State, Province, Country: CA
#1

07-24-2022, 05:56 PM
I just acquired a "Philco / Ford M3850T" and I am looking for a schematic.  I've tried PhilcoRadio.com and any other sources I could think of but keep coming up empty.  Sams Photofact has something but I think it's wrong.
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

07-24-2022, 07:06 PM
Hi and welcome,

I took a look around but didn't see much either. Seems it circa 1966 but not listing for that particular model. Bare in mind that just about all the set we discuss are from 1928-1960 and most vacuum tube. Sam's might be only source for info.
Good luck!
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
dannyb
New Member
*
Posts: 2
Threads: 1
Joined: Jul 2022
City: Martinez State, Province, Country: CA
#3

07-24-2022, 07:22 PM
Thank you so much for the reply, Terry. I sincerely appreciate your time, and I'll keep digging. It may be that an old fashioned visit to my local library is in order!
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Vintage Hi-Fi, Stereo and Audio