1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 40-180 Volume
gdolph
Junior Member
**
Posts: 12
Threads: 1
Joined: Aug 2022
City: Calgary State, Province, Country: Alberta
#1

10-24-2022, 06:45 PM
I have a couple of Philco Model 40-180s that I have been working on. Both have been recapped and out-of-spec resistors replaced. My problem is that the maximum volume on both is not as loud as I would like. When I touch the top of the converter tube 6J8G (shows up as 7J7 in any schematic, as per production change run 4), volume improves dramatically for both. Any thoughts on what is causing this and how to make this volume improvement permanent?


Attached Files Image(s)
   
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

10-24-2022, 08:17 PM
Hi and welcome to the Phorum,

I would check #13 the plate choke for the rf amp isn't open and that the loop ant is connected properly.

Here's the Philco service info for your set. https://philcoradio.com/library/download...20Book.pdf

GL
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 10-24-2022, 08:23 PM by Radioroslyn.)
Find
radiorich
Phorum Expert
*****
Posts: 1,600
Threads: 101
Joined: May 2008
City: Omak State, Province, Country: WA
#3

10-24-2022, 08:24 PM
Hello gdolph,
welcome aboard and I agree with terry and I would also Add they might need some alighment too !

Sincerely Richard
Find
morzh
Odobenus rosmarus
*****
Posts: 15,818
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
#4

10-24-2022, 09:29 PM
I will second...third Terry's suggestion. Very typical symptom.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 10-24-2022, 09:30 PM by morzh.)
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently 5366 online users. [Complete List]
» 4 Member(s) | 5362 Guest(s)
AvatarAvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration