Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Antennas
#1

Hi guys. I've been MIA for a few years, moving house a couple times among other significant events keeping me from this hobby.

I listened to my Model 20 a fair amount during 2020 while working from home until the power stopped working. I finally had a look and discovered a poor original wire from the power switch. Replaced and it's back in business (except for an issue of occasional good signal that becomes poor and drops as the set warms up over a couple minutes. My original thought was a hot tube issue, but will start looking into it more this spring).

Now that I'm settled in a house, I'm thinking of improved reception for my radios. What do you guys think of a roof aerial or something mounted in the attic? I've used an assortment of plain wire antennas over the years that have been "ok", but would like better performance overall. I'm about 30 miles southwest of Chicago and can pick up a couple stations pretty well, but not much else. I'd like to listen to something besides the ballgame and political talk radio.

Greg

"We are here to laugh at the odds and live our lives so well that Death will tremble to take us."
#2

Quote:I'm thinking of improved reception for my radios. What do you guys think of a roof aerial or something mounted in the attic?
Good idea Icon_biggrin 

Give it a good ground too, short and direct to earth, not the ground for the wall outlet...

Chas

Pliny the younger
“nihil novum nihil varium nihil quod non semel spectasse sufficiat”
#3

Quote:Give it a good ground too, short and direct to earth, not the ground for the wall outlet...

I figured I'd run a long wire to the basement and ground it to the water main from the city. It's copper and certainly underground!

Greg

"We are here to laugh at the odds and live our lives so well that Death will tremble to take us."
#4

Hi Greg, as for an antenna, I’ve had great results using my landline phone line. In most homes, there are 4 wires in the line coming in. 2 of them are fore the phone and the other 2 have nothing on them. I hooked a .001mfd cap to either one of those and run a wire to my radio. That gets me about 60’ or more of antenna running from the house, up high and out to the pole on the street plus the extra footage run throughout the house. And now since we’ve done away with our home phone, I can put my radio in any room in the house and have access to that antenna from any phone Jack.

Ron

Bendix 0626.      RCA 8BX5.   RCA T64
Philco 41-250.    Philco49-500
GE 201.             Philco 39-25
Motorola 61X13. Philco 46-42        Crosley 52TQ
Philco 37-116.    Philco 70
AK 35                Philco 46-350
Philco 620B.       Zenith Transoceanic B-600
Philco 60B.         Majestic 50
Philco 52-944.    AK 84




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM

[-]
Who's Online
There are currently 2638 online users. [Complete List]
» 2 Member(s) | 2636 Guest(s)
AvatarAvatar

>