Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Another Philco 44 variant?
#1

Ron and friends,

Here's a Philco model 44 highboy that I'm repairing for someone. This has a cabinet like some other models (43, 47, others) from 1933. However, you don't have a model 44 in this cabinet in the Gallery.

[Image: http://antiqueradios.com/gallery/d/12560..._front.jpg]

[Image: http://antiqueradios.com/gallery/d/12560...4_back.jpg]

Here's the chassis label:

[Image: http://antiqueradios.com/gallery/d/12561..._label.jpg]

There is also a label on the inside of the cabinet wall indicating model 44.

Is this a new one to add to the list of model 44 variants?

Tom
#2

Hi Tom

I would say so.

It is apparent that Philco's Furniture History records are incomplete, as this is not the only Philco cabinet from that time period (1932-34) that is not documented. I just checked Philco Furniture History again, and no, this 44 is not mentioned.

Would you please send me a larger (higher resolution) photo of that 44 so that I may add it to the Gallery? Thanks in advance.

mr.philco AT yahoo DOT com

BTW - very clean radio! You don't often see sets this nice.

--
Ron Ramirez
Ferdinand IN
#3

I'll send you some pictures now. The radio is very clean, and that's the original finish. One of the best original finishes I've seen on a radio that old.

Would you think it likely that this cabinet style came after the 44 highboy you've got in the gallery? Looking at Philco highboy cabinet trends, this somewhat less ornate style looks to me like it may have been a later version, but I certainly can't say for sure.
#4

Pictures received, and photo posted in the Gallery (Fall 1933 page). Thanks, Tom! Icon_smile

It's hard to say whether your 44H was issued before or after the 44H which was already shown in the Gallery. Like you, I would tend to believe it came later, but I cannot say for sure since it is not documented.

--
Ron Ramirez
Ferdinand IN




Users browsing this thread:
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM
Philco 38-7 Speaker
7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM
40-150 General questions
I discovered a stamp on the underside of the breadboard on my Philco 40-150. It is"56-1417' in black ink with numbe...Kevin_D — 07:14 AM
Philco 38-7 Speaker
FYI the Impedance of the HR20 (the one I have) secondary of the audio transformer is 5 ohms. The 38-7XX speaker is suppo...tludka — 04:22 PM
Philco 38-7 Speaker
Yeah, don't use the transformer currently on the H-20 (Dopf, I thought "H20, is that new technology, a speaker usin...MrFixr55 — 03:51 PM

[-]
Who's Online
There are currently 2769 online users. [Complete List]
» 2 Member(s) | 2767 Guest(s)
AvatarAvatar

>