Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Unusual Crosley table radio
#1

I just picked up an unusual and rather large table radio built by Crosley today. I was so stunned when I saw it that I didn't even haggle the price! It's even bigger than my RCA 140 tombstone, but for a reason as it is a battery set. One of the best condition battery sets I have ever run across. Good cabinet, complete, and unmolested in any way. Even all the original battery leads are there, though I'll probably have to rework that if I ever go to power this set up. The chassis number and schematic number for this radio is 535 and the Crosley sites list this radio as the "Battery Fifty-Two". Other than that and the schmatics I found on nostalgia air, this radio draws a blank in my web searches so far. So, I wonder, did I get a real jewel or a lump of coal? Battery (farm) sets are always tricky and this thing is a monster of a table radio. Thankfully it doesn't weigh as much as the RCA 140! Icon_lol

No matter where you go, there you are.
#2

Neat Radio!!! Personally I often go after battery sets for the reason depicted by your Crosley. They are often in excellent original condition. The electronics are simple and usually one like yours will only require verifying that it is electrically sound. I do not recommend "jury-rigging" a power source for one unless you are VERY sound electrically, as DC voltage is inherently more dangerous than AC, and these battery sets draw a fair amount of DC current. (If im talking down to you, PLEASE forgive me.)
I recently aquired a Crosley 128 cathedral battery powered set. It is 3V A batt, 135V, 22.5V B batt, and after a mild rework, it WORKS !!!! It's an 8 tube model, with 2- 31 tubes as triode-pushpull output. NEAT set.
#3

Sounds like your voltages are the same as mine. Oddly, mine lists the 22.5 voltage as the 'C' battery. I was a bit miffed to find out all the tubes but one were totally burnt out. The other tube was a dead short. Managed to find replacements for them all today but the 1B5. Going to dig through the tubes I just got last week for that one. I'm wondering if the radio has a short or if someone connected too high of a battery to the 'A' supply.

No matter where you go, there you are.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
IF can wire size and Rubber mounts?
Hello PHORUM members, I am still working on restoration of my PHILCO 37-640.  I want to start with rewiring the IF ca...georgetownjohn — 06:32 PM
Gilfillan Brothers Car Radio?
There is a Mission Bell model 19/19A that could be what you’re looking for, Riders vol 4. It has the tube line-up of: 0Z...Joe Rossi — 05:01 PM
Looking for verification of correct schematic.
Definitely 870044RossH — 01:12 PM
12' Philco
Wonder if the chassis was big too.daveone23 — 12:38 PM
Philco 38-2 Automatic Tuning
Hi Ron, I have sent Radio Daze my concerns with the dial so I guess we will see. They used my original to make the repro...dconant — 12:27 PM
Hickok AC51 tube tester
How does the  5W4 and 83 tube filaments get fed?martinj — 12:25 PM
462ron
Hi Dan, your original dial appears to be lighter, easier to allow light through. My original is similar except it’s crac...462ron — 12:07 PM
Philco 38-2 Automatic Tuning
I received my new 38-2 dial. I'm a little disappointed. As you can see in the picture the blues have a white shadow. The...dconant — 11:13 AM
Philco 38-2 Low Volume
I have been playing my 38-2 for a while now and it is doing very well. I did have to replace the 6A8 (osc) as it develop...dconant — 11:03 AM
Philco Speaker Spider
Hello, Does anyone with a 3 D printer make the spiders for those old Philco speakers? That might be a good idea for some...dconant — 09:41 AM

[-]
Who's Online
There are currently 4055 online users. [Complete List]
» 1 Member(s) | 4054 Guest(s)
Avatar

>