1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Texasrocker are you out there? Another cap question.
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#1

11-12-2011, 09:52 PM
I know you have some reference which is better than that posted on the work bench. Another one of those dang philco bakelite stuff caps I can't find a reference to. Its a 3903AB. I know it has one cap in it, can you tell me what it is? Add another as an edit, the 3903T. Single cap, what is it? One more, not on the bench list, a 7025D. Any help appreciated.

Thanks Jerry
A friend in need is a pest!  Bill Slee ca 1970.
Find
Bradley Rush
RadioMonkey
***
Posts: 220
Threads: 56
Joined: Oct 2011
City: Lompoc CA
#2

11-13-2011, 01:11 AM
3903AB= 3903OSU
ONE ,01 UF 600V
Find
Bradley Rush
RadioMonkey
***
Posts: 220
Threads: 56
Joined: Oct 2011
City: Lompoc CA
#3

11-13-2011, 01:13 AM
3903T = 39030SU
ONE .01 UF 600V
Find
Bradley Rush
RadioMonkey
***
Posts: 220
Threads: 56
Joined: Oct 2011
City: Lompoc CA
#4

11-13-2011, 01:15 AM
SERVICE BULLETIN NO. 289
Is where I found the info
Find
Bradley Rush
RadioMonkey
***
Posts: 220
Threads: 56
Joined: Oct 2011
City: Lompoc CA
#5

11-13-2011, 01:19 AM
no 7025D

but
7625D
3-4 .015 uf 600v
1-5 .006 uf 600v
Find
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#6

11-13-2011, 03:56 PM
Thanks TROG, got me off and running again. Will have to check on the 7025D, perhaps I missread it and it was a 7625D.

Jerry
A friend in need is a pest!  Bill Slee ca 1970.
Find
Texasrocker
Phorum Expert
*****
Posts: 909
Threads: 117
Joined: Jun 2007
#7

11-16-2011, 12:41 PM
Sorry for the delay getting here Jerry. Been real busy lately. Looks like you have the specific caps info you needed now. Always glad to help if I can, you can also pm me, as I'm not on the forums each and every day.
Find
« Next Oldest | Next Newest »




Users browsing this thread:
[-]
Recent Posts
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM

[-]
Who's Online
There are currently 3336 online users. [Complete List]
» 3 Member(s) | 3333 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration