Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Hi all here is my latest toy
#1

I found this little tumbstone and could not resist. Icon_smile The cabinet needed a lot of glue and repair Icon_sad but I think it come out o k. As you can see from the pictures it was in bad shape. It is the first Crosley I have ever messed with, notice the caps were dual, two in one paper tube with the common comming out at the mounting ring and soldered to the ring. Icon_think I had never seen this set up. Anyway here is the pictures
here is how I got it
[Image: http://i927.photobucket.com/albums/ad118...C03634.jpg]
[Image: http://i927.photobucket.com/albums/ad118...C03634.jpg]
Here is the dual caps
[Image: http://i927.photobucket.com/albums/ad118...C03632.jpg]
and what I ended up with
[Image: http://i927.photobucket.com/albums/ad118...C03638.jpg]

Joe

Joe Bratcher near Louisville, KY
#2

Joe

It looks nice.
Is it playing yet?
#3

Hi
Yes it plays very good, it has no AVC, so tuning is tricky but after tuned in it works fine . The volume control is at the antenna input. I just could not pass it up. Joe

Joe Bratcher near Louisville, KY
#4

Nice little Crosley! Yes, Crosleys can be good performers once you get them going. But, since Crosley radios were built with an eye towards low cost, you can run into many headaches in them as well. Still, I love the art-deco Crosley tombstone I've got. Think I will get it out after work and enjoy it some this evening. Icon_smile

No matter where you go, there you are.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4.RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM

[-]
Who's Online
There are currently 3042 online users. [Complete List]
» 2 Member(s) | 3040 Guest(s)
AvatarAvatar

>