Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 71
#1

Hi Guys,
Check this one out.
A friend of mine found this in a junk shop for $35 a few months ago. He capped it out, changed the speaker wire(s) and it came to life. He decided he did not want it so I purchased it for $35. Did I do ok? Is this a rare bird or is it pretty common? Right now it is painted brown so tomorrow I am going to strip and see what is underneath. Just goes to show a guy never knows where an old bone will surface.

Bob


Attached Files Image(s)
   
#2

Yes, even painted, you did great for $35. Icon_thumbup

--
Ron Ramirez
Ferdinand IN
#3

Gosh, yes, that is a great deal.
#4

Thanks!
It's my first cathedral so I know nothing about them as far as production numbers, and where they line up high end to low end. All I really know is I like the looks of the 80B the best.
#5

Looks like he got the replacement grille cloth from the same place as Foggy. The model 71 is the 1932 equivalent of a Philco 70, except it uses 6.3 volt tubes I think, and the cabinet is different of course.
Regards
Arran
#6

It also has avc the 70 doesn't.
Terry
Good deal!!
#7

Yes, a fantastic dealIcon_biggrinIcon_biggrinIcon_biggrin

Steve

M R Radios   C M Tubes
#8

Hi Bob,
You did really good on the set.
Hopefully, the paint has protected the veneer underneath.
Worse case, it is heavily sanded in different directions Icon_eek

You can always re-veneer, that's a nice looking set.




Users browsing this thread:
[-]
Recent Posts
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM

[-]
Who's Online
There are currently 3199 online users. [Complete List]
» 3 Member(s) | 3196 Guest(s)
AvatarAvatarAvatar

>