Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Are all 116X electrolytics negative ground?
#1

I've finally caught up a bit and gotten back to the 116X. My eyes are getting funny and I'm driving myself nuts trying to trace the schematic so before Jack Daniels and I settle in for the night, are all 116X electrolytics negative ground? The radio played and then I replaced the electrolytics. Now it hums and with the variac set at 90 volts, the ammeter slowly climbs up and goes past 3 amps before I shut it down. Nothing smokes or acts goofy otherwise. I've tripled checked (and more) the lytics and they seem to be installed correctly, hence the question, do I have one (or more) bass ackwards?

[Image: http://i863.photobucket.com/albums/ab191...tic-1b.jpg]

[Image: http://i863.photobucket.com/albums/ab191...tic-1c.jpg]

Thanks,
Larry
#2

Larry

All are negative ground save one: the 10 uF, 100 volt cap connected from B- (center tap of high voltage secondary) to ground. That one has its positive lead going to ground, and the negative lead to B-.

Before I hit the "Post Reply" button, one clarification: Caps (103) and (104) have their negative leads going to B-.

--
Ron Ramirez
Ferdinand IN
#3

Thanks Ron, much appreciated. I think I'll let my head clear for a day and tackle it tomorrow evening. Icon_smile

Larry




Users browsing this thread:
[-]
Recent Posts
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM
The list of my radio & TV collection!
Magical chords of forgotten melodies, old nostalgic music on an old radio... Saturday night blues on the Mid-Waves on an...RadioSvit — 12:20 PM
Philco 42-345 Restoration/Repair
Thank you MrFixr55 the issue with this radio is that the internal coil antenna is missing and there was a wire in its pl...osanders0311 — 11:34 AM
Philco 610B oscillator wiring
Regarding the oscillator circuit which is comprised of the 6A7's cathode, control grid, and screen grid. These elements ...Radioroslyn — 10:33 AM
Philco 42-345 Restoration/Repair
Hi OSanders, First off, welcome to the Philco Phorum where Phine Phamily-Phriendly Pholks Phull of Philco Phacts and P...MrFixr55 — 08:41 AM
Philco 42-345 Restoration/Repair
Today I've been reading through the site trying to learn more about this radio. I also soldered the lose power cord cabl...osanders0311 — 08:24 PM

[-]
Who's Online
There are currently 2410 online users. [Complete List]
» 1 Member(s) | 2409 Guest(s)
Avatar

>