Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

37-610
#16

+1 what Arran says. If I'm goingf to spend a considerable amount on a radio, I prefer natural wood grain every time! Take care. Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#17

I have many sets in cabinets that are mezza-mezza but play well and had a clean chassis to work with. Though a nice shelf Queen is pretty too. Where I like to listen to the radios I live with the the water stains, cigarette burns, maybe refinish when really poor....
Good Hunting.

Paul

Tubetalk1
#18

I have a 37-610 ..Just because its only five tubes do not even think for a minute that you should not purchase to put into your collection. It is super picks up stations from all over. I love mine would not give it up. My faux wood grain has two very little scratches. One of the very first radios I ever purchased. Keith Park did the electronic resto thats why it works go good. I am still trying to get the handle of doing one myself.
#19

I don't believe Arran meant to slam the 610!

I have owned several 610s and 37-610s, and agree that they do very well for a five-tuber. Philco made some swell five-tube sets!

But relatively speaking, for 200 dollars you can get a lot of radio. From a standpoint of sensitivity, selectivity, and quality volume, the 610 does not perform as well as other models with more tubes/features that you could get for 200 dollars. In fact, I got my 37-116 for 200, and my 38-116 for less, and both are in nice shape.

The 610/37-610 was closer to a base model set, albeit a good playing one.

The 200 dollars spent on the 37-610 was doubtless due to it's condition. For many folks that is what they are looking for.
#20

$200.00 dollars is a whole lot to pay for that radio... but is a good performer for a five tube radio.
#21

No I wasn't bashing the 37-610 in and of itself, I just wouldn't think of paying $200 for one just because the faux grain is in nice shape. Because these sets were a near entry level model there were a lot of them produced. While the faux grain is bad on a lot of them it's not like it's anywhere near impossible to find one where the grain, if not pristine, is at least restorable like the front panel on Bob's 38-62.
Regards
Arran
#22

+1 Icon_thumbup




Users browsing this thread:
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Today I've been reading through the site trying to learn more about this radio. I also soldered the lose power cord cabl...osanders0311 — 08:24 PM
Philco 610B oscillator wiring
Thanks David! I do have that same later prodution model 610 schematic. I've also studied the Philco service bulletins fo...Tubester — 08:12 PM
Philco 610B oscillator wiring
Some info from Beitmans says late production. David   David — 06:06 PM
Restoring Philco 96
Oh wow! Just found this thread.  Brings me back to early days on this phorum.  I did a 96 back in 2017.  Thread here: ...rfeenstra — 06:05 PM
Philco 610B oscillator wiring
Thanks for the replies. It's not the really the hum that I am after. Just trying to understand why only the shortwave ba...Tubester — 04:01 PM
Restoring Philco 96
70 and 90 are Superhets, but at least the 2x45 model of 90 uses the Plate detector (and so does 70). Also the Atwaters,...morzh — 03:28 PM
Restoring Philco 96
Morzh, Prayers for your mom. I am sure that there was enough pain living through the Holocaust as a child. I pray dail...MrFixr55 — 02:19 PM
Philco 610B oscillator wiring
Hi Dan, Divide and conquer. First off trry to differentiate between 60Hz and 120 Hz hum. 120 Hz hum has a higher pit...MrFixr55 — 01:49 PM
Restoring Philco 96
Yes, other than takin a toll on your back, they are undeed way more repair friendly than many other Philcos. To me, som...morzh — 01:04 PM
Philco 610B oscillator wiring
If the wires look like they were this way from the factory (very neat and very dull soldering joints), I'd leave them be...morzh — 12:58 PM

[-]
Who's Online
There are currently no members online.

>