1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
42-350 antenna
radiodocs
Junior Member
**
Posts: 6
Threads: 1
Joined: Jul 2013
City: Los Angeles, California
#1

08-06-2013, 05:25 PM
I'm restoring a model 42-350 and doing fine with it except that
the radio was shipped to me with the AM/SW loop antenna detached
from the cabinet. I'd like to get it back in original shape (no improvisation). Can anyone shed some light on how it was originally
secured? Or perhaps a close-up photo?
Thanks,

John Michael
Find
Eric Adams
Phorum Expert
*****
Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages State, Province, Country: Florida
#2

08-06-2013, 11:50 PM
John,
I think this is what you are looking for. The antenna is secured with small nails.


Attached Files Image(s)
   
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

Website Find
Arran
Phorum Expert
*****
Posts: 4,705
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#3

08-07-2013, 12:22 AM
On my 42-327 with a very similar heavy gauge wire loop, the antenna was attached to the cabinet with some shot Phillips head screws.
Regards
Arran
Find
Jim Dutridge
Senior Member
****
Posts: 290
Threads: 54
Joined: Mar 2007
City: Toledo State, Province, Country: OH
#4

08-07-2013, 08:42 AM
I've also seen these secured with large thumbtacks.
Find
radiodocs
Junior Member
**
Posts: 6
Threads: 1
Joined: Jul 2013
City: Los Angeles, California
#5

08-08-2013, 05:12 PM
Thanks for all the replies. Arran, I suspected it might be small Phillips head screws that secured the antenna, as my 48-482, which appears to be a close cousin (or perhaps younger brother) to this radio has the same antenna and is secured with them.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! GaryGarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM

[-]
Who's Online
There are currently 4268 online users. [Complete List]
» 2 Member(s) | 4266 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration