1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
38-2670 cabinet problem
thirtiesradio
Senior Member
****
Posts: 344
Threads: 38
Joined: Jun 2011
City: Tustin State, Province, Country: California
#16

10-08-2014, 11:38 PM
You can install veneer on a sharp radius horizontally by soaking it in veneer softener and using the cabinet as a form. Once dry you can trim and install it. They used steam in the old days......some cabinet makers still do although most use bending irons, heat blankets and vacuum forms. I'm sure there are other ways as well.
(This post was last modified: 10-08-2014, 11:49 PM by thirtiesradio.)
Find
murf
Senior Member
****
Posts: 669
Threads: 145
Joined: Jun 2011
City: Elko,MN.
#17

10-26-2014, 02:01 PM
Ok,
Here is the finished cabinet guy's.[Image: http://i1161.photobucket.com/albums/q509...abinet.jpg]
Find
sam
Phorum Expert
*****
Posts: 2,570
Threads: 336
Joined: Jun 2013
City: lawrenceville nj
#18

10-26-2014, 02:29 PM
looks great murf Icon_clap
Find
Eliot Ness
Phorum Expert
*****
Posts: 3,122
Threads: 57
Joined: Apr 2011
City: Lexington, KY
#19

10-26-2014, 02:36 PM
That turned out very nice Icon_thumbup
John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
Find
klondike98
Phorum Moderator
******
Posts: 5,060
Threads: 269
Joined: Nov 2012
City: Bandon State, Province, Country: OR
#20

10-26-2014, 02:46 PM
Great save murf!!!  Looks great  Icon_clap Icon_clap Icon_clap
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
thirtiesradio
Senior Member
****
Posts: 344
Threads: 38
Joined: Jun 2011
City: Tustin State, Province, Country: California
#21

10-26-2014, 09:16 PM
Very nice!
Find
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#22

10-27-2014, 01:12 PM
Murf, what a great job. Congrats
Jerry
A friend in need is a pest!  Bill Slee ca 1970.
Find
« Next Oldest | Next Newest »




Users browsing this thread:
[-]
Recent Posts
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM
Philco 38-7 Speaker
7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM

[-]
Who's Online
There are currently 2756 online users. [Complete List]
» 3 Member(s) | 2753 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration