1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
zenith 7s330 alignment
fields 100
Member
***
Posts: 228
Threads: 64
Joined: Dec 2013
City: Northbrook, IL
#1

12-02-2014, 10:41 PM
Alignment instructions for the set are laconic to say the least. For the IF -connect osc. to converter grid, 455K.C.,
dummy ant. .5 uF. What does it mean? Do I just inject 455 K.C. from my sig. generator to the converter grid via
.5 uF cap? Same with a "set to scale" procedure - 18 M.C., dummy ant. 400 ohms. Is it their terminology or I just got spoiled by the nice Philco detailed instructions i.e. "connect signal generator to the grid of tube such and such via 200pf capacitor etc, etc... Thanks.
P.S. It is 7S530.




http://www.nostalgiaair.org/PagesByModel...025333.pdf
(This post was last modified: 12-02-2014, 10:58 PM by fields 100.)
Find
codefox1
Silent Key
*****
Posts: 2,128
Threads: 18
Joined: Oct 2008
City: Merrick, Long Island, NY
#2

12-05-2014, 10:41 PM
Well, .5 is a little large for a coupling capacitor, sure you don't mean .05 mfd? Should work anyway. Since this is a transformer set, you don't have to sweat the ground connection. Dummy antennas? Well for regular AM sets with their own loops, about 30 turns of whatever on an empty TP cardboard works to couple generator to radio without direct connection works for me, but for 18 MC, dunno.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM

[-]
Who's Online
There are currently 3429 online users. [Complete List]
» 4 Member(s) | 3425 Guest(s)
AvatarAvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)