Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

philco 39-19 with turntable
#1

This was left in a house I purchased, and I have not been able to find anything out about it.  Any chance anyone can tell me anything?


Attached Files Image(s)
               
#2

Welcome to the Phorum!  Looks like you have a model 39-19PF .  The 39-19 radio chassis was used in several different phono models.  You can get schematic info from Chuck Schwark for only a few bucks. Ron, this site owner, may have interest in photos of your unit since he doesnt have actual photos in the gallery.  Nice find.
#3

It looks to be in pretty good shape but unless the electrolytic and paper capacitors have been replaced in the recent past you should not try to plug it in.  The wiring in 1939 models can also be a bit dicey and should be checked.  Lots of friendly folks here to help.

Some info is also available on-line at:
http://www.nostalgiaair.org/Resources/280/M0013280.htm  and
http://www.nostalgiaair.org/PagesByModel...013283.pdf
#4

I have the table model of this radio, never knew they made a console version with a phonograph!

No matter where you go, there you are.
#5

WOW
beautiful, looks show room new
hard to believe some one left it their
sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#6

Now that is a great find! Icon_thumbup It's one of those sets that is rarer than hen's teeth but won't have much monetary value as it isn't in high demand. Most people who buy consoles want one with lots of tubes and lots of SW as well as AM. This set, while it is rare and looks very nice, is more cabinet than substance.

As Bob (klondike98 ) already mentioned, I would truly appreciate several good photos of your set for inclusion in the Gallery. This set needs to be well documented. As an example, until I saw your photos I did not know this model used the same oddball, linear tracking phono pickup as used in the earliest Philco table model phonos (39-10TP, 39-12RP, and the later RP-3).

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM
Philco 38-7 Speaker
7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM

[-]
Who's Online
There are currently 3052 online users. [Complete List]
» 2 Member(s) | 3050 Guest(s)
AvatarAvatar

>