Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Zenith Transoceanic battery-opinion
#1

Hi Guys,
I am finishing up my A600 Transoceanic and once it is finished it will be for sale. My question is whether I should go through the trouble to build a battery pack(these batteries are no longer available) or just sell it to run on A/C. The battery pack will cost me about $45.00 to construct plus the cost of 10 9 volt and 4 D cell batteries.
What do you think? Since it will not be an original battery, will it still be important to a buyer/collector?

Thanks,

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#2

eric
I don`t think it would be worth it to make battery
would increase 50. to 75. more for radio
as most don`t play them often or ones that do have batteries play very little from what I seen
sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#3

 If your intent is just to fix this T.O up for resale I think that making a battery pack for it is a waste of time. I don't think it would add much, if any value, to a 600 series T.O, those seem to be among the most common tube T.O models you can find. Since these were all so called "three way" portables most people would just operate them from a line cord, if they wanted one that would be practical to run from batteries they can always pick up a later transistor model T.O. 
Regards
Arran
#4

Unless you want to sell the battery you make for a profit.
But: You cannot be sure that whosoever buys it will want the battery.
And: this whosoever can buy a battery from people who build and sell them should he ever want it.
#5

Icon_thumbup Thanks guys. I tend to agree with all of you.

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org





Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM
Philco 38-7 Speaker
7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM
40-150 General questions
I discovered a stamp on the underside of the breadboard on my Philco 40-150. It is"56-1417' in black ink with numbe...Kevin_D — 07:14 AM
Philco 38-7 Speaker
FYI the Impedance of the HR20 (the one I have) secondary of the audio transformer is 5 ohms. The 38-7XX speaker is suppo...tludka — 04:22 PM
Philco 38-7 Speaker
Yeah, don't use the transformer currently on the H-20 (Dopf, I thought "H20, is that new technology, a speaker usin...MrFixr55 — 03:51 PM

[-]
Who's Online
There are currently 2775 online users. [Complete List]
» 2 Member(s) | 2773 Guest(s)
AvatarAvatar

>