1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
philco 41-245
sam
Phorum Expert
*****
Posts: 2,570
Threads: 336
Joined: Jun 2013
City: lawrenceville nj
#1

02-22-2015, 12:43 AM
hey guys
bought a radio for parts  not too bad shape
decided to restore it some one installed head phone jacks ? least I think they are
found the speaker wire cut  from fiber board to speaker cone.  copper ribbon wire string in it ?
how do I solder a piece of wire to it
I replaced lytics and tubes ,jumped speaker It plays but low and static
sam 
Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
Find
morzh
Odobenus rosmarus
*****
Posts: 15,444
Threads: 539
Joined: Oct 2011
City: Jackson, NJ
#2

02-22-2015, 10:22 AM
Sam

Could you show some pics, I have some trouble picturing it in my head....
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
simplex1040
Member
***
Posts: 86
Threads: 15
Joined: Sep 2012
City: Paducah, KY
#3

02-27-2015, 12:38 PM
I think he means one of the wires to the voice coil is cut. I would just take a small piece of wire and make a loop on the wire and on the remaining voice coil braid wire and solder a patch on it. Then solder your extended wire back to the terminal.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM

[-]
Who's Online
There are currently 2727 online users. [Complete List]
» 3 Member(s) | 2724 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration