Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

E.H.Scott Military Receiver RCH
#1

Here is a receiver that I friend in Illinois gave me. He had no idea of what it was. I think its a E.H. Scott RCH receiver. Here are some pictures..
[Image: http://i292.photobucket.com/albums/mm38/...xor1cg.jpg]
[Image: http://i292.photobucket.com/albums/mm38/...c5nrtk.jpg]
[Image: http://i292.photobucket.com/albums/mm38/...0dhu0d.jpg]

No markings on it anywhere .. Its missing the name plates..

It seems to match this picture of a RCH..
[Image: http://i292.photobucket.com/albums/mm38/...sa8pug.jpg]

Can anyone positive ID this?

Thanks
Skip...
#2

No expert on these Skip but the chassis picture on the RCH sure appears to match what you have perfectly as far as I can see.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#3

Better keep up on ur vitamins!!! Looks like a backbreaker!!!!
Don't know much about your rx. Have seen a few over the years but never took one home.
You may try the ARC-5 forum over at yahoo. They discuss some other military stuff other than ARC-5 stuff.
Terry
#4

Ok thanks for the info.. Its built like a tank.. Covers ..

[Image: http://i292.photobucket.com/albums/mm38/...tbyox6.jpg]

I think it was used on Navy ships. Receives well. I did download the manual.. I am going to do a full alignment and then probably sell it.. No room for it as I have my 2 R-390's , the Collins R-388 and a Big old Hallicrafters SX-101 RX and the HT-32 Transmitter.. which take up a lot of room..


Thanks
Skip...
#5

Tis easier to buy a bigger house.  

Terry
#6

    These were also used in a Mackay shipboard communications console after the war, under the designation SLR-F.
#7

Very Interesting..

Thanks
Skip...




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM
Philco 38-7 Speaker
7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM
40-150 General questions
I discovered a stamp on the underside of the breadboard on my Philco 40-150. It is"56-1417' in black ink with numbe...Kevin_D — 07:14 AM
Philco 38-7 Speaker
FYI the Impedance of the HR20 (the one I have) secondary of the audio transformer is 5 ohms. The 38-7XX speaker is suppo...tludka — 04:22 PM
Philco 38-7 Speaker
Yeah, don't use the transformer currently on the H-20 (Dopf, I thought "H20, is that new technology, a speaker usin...MrFixr55 — 03:51 PM

[-]
Who's Online
There are currently 2475 online users. [Complete List]
» 1 Member(s) | 2474 Guest(s)
Avatar

>