Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Would You touch this wi th a ten' pole?? I need my head examined!!!
#16

Can't speak for the ten foot pole, but I'm a six foot Pole and I wouldn't touch it!!  Take care, Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#17

If it's the xtal I found the guy is out of he mind! I sent a offer will see.

Terry
#18

Hey Sam,
Maybe shock treatment just might help ME!!!!
I do get a dose of it every once in while when I'm not paying attention.

Terry
#19

Arron says it works 
Will it fit in 5 gall bucket ?
Do you have battery charger  and steel ?
Let me know I will come over next Sunday 
With what you need and try 
Ps I'm only coming over to Video tape it so 
I can post on phorum Icon_twisted

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#20

Ya know I've never sat in a 5G bucket of Borax before!!! Sound like fun!!
Aren't you at work????

Terry
#21

Icon_lol Not you silly the chassis
Yes at work I get break time and lunch time 

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#22

(08-13-2015, 08:08 PM)Radioroslyn Wrote:  Ya know I've never sat in a 5G bucket of Borax before!!! Sound like fun!!
Aren't you at work????

Terry

 Washing soda, or baking soda, but it only works with steel or iron. I thought of trying Borax but I've never heard of anyone else doing that.
Regards
Arran
#23

Just cleaned a solid brass table lamp with my electrolysis bucket using washing soda and a deep cycle 12 volt battery.  It came out looking like new!  Did a much better job than buffing with Simichrome compound.  Take care, Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#24

Wow, Terry: those are some rough project sets BUT that is the way to afford-ably get an uncommon set. The caveat is having the knowledge coupled with the "will do" to get it right. 

But I know you have large amounts of both qualities and will soon have 'em good as new.  
#25

I think I need a new coupling capacitor!!!
See ya in a few weeks!!

Terry




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

[-]
Who's Online
There are currently 6698 online users. [Complete List]
» 1 Member(s) | 6697 Guest(s)
Avatar

>