1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Bakelite capacitor block
jmac3ky
Member
***
Posts: 65
Threads: 23
Joined: Mar 2013
City: Murray, KY
#1

07-17-2017, 08:35 PM
Restoring a Philco 650 and have 6 of the bakelite capacitor blocks to rebuild. I used to go to the Philco site where there was a section of diagrams showing internal wiring for the different blocks. With the remake of the site the list and the diagrams are gone. Anyone know where the information exists?

The other parts values are missing as well. Help.

Thanks.
(This post was last modified: 07-17-2017, 08:37 PM by jmac3ky.)
Find
sam
Phorum Expert
*****
Posts: 2,572
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
#2

07-17-2017, 08:40 PM
Find it here  
http://philcoradio.com/phorum/showthread.php?tid=14964

The book was just listed very good book too   Icon_thumbup
http://philcoradio.com/phorum/showthread.php?tid=16946

Sam
Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
Find
jmac3ky
Member
***
Posts: 65
Threads: 23
Joined: Mar 2013
City: Murray, KY
#3

07-17-2017, 09:22 PM
Sam,

Thanks so much. I'm in your debt God Father.

John
Find
PhilcoPhan1936
Jeff W.
******
Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro State, Province, Country: AR
#4

07-17-2017, 10:55 PM
If you're referring to the Philco Repair Bench, try the Wayback Machine. The entire old site is archived.

https://web.archive.org/web/201603242327...lokcap.htm
Blessings,
Jeff W.
Jonesboro, Arkansas

http://jeffsradios.weebly.com

God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Find
jmac3ky
Member
***
Posts: 65
Threads: 23
Joined: Mar 2013
City: Murray, KY
#5

07-18-2017, 07:47 AM
Thanks Jeff. Great find.
Find
PhilcoPhan1936
Jeff W.
******
Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro State, Province, Country: AR
#6

07-18-2017, 10:50 AM
(07-18-2017, 07:47 AM)jmac3ky Wrote:  Thanks Jeff. Great find.

I'm afraid I can't take credit. Someone else here on the Phorum pointed it out recently.

Once I saw it, I immediately went through all the archived pages and saved PDFs as a reference. Icon_thumbup
Blessings,
Jeff W.
Jonesboro, Arkansas

http://jeffsradios.weebly.com

God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Find
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#7

07-18-2017, 10:58 AM
Chuck is in the process of updating his Philco Repair Bench website so the info should all reappear there in time.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

[-]
Who's Online
There are currently 6824 online users. [Complete List]
» 1 Member(s) | 6823 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration