1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Question on Shielded Capacitor for Philco 38-3
LarryFS
Member
***
Posts: 120
Threads: 15
Joined: Aug 2017
City: Fort Worth State, Province, Country: TX
#1

04-22-2018, 07:49 PM
I'm ready to start refurbishing the RF unit of a Philco model 38-3.  I'm wondering about a .05 mfd capacitor (item 13 in the parts list) that is shielded (see photos below).  Do I need to ensure the replacement metal film tubular capacitor is also shielded?

Thanks,
Larry


Attached Files Image(s)
       
Find
Phlogiston
Radio-Fixer-Upper
*****
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
#2

04-22-2018, 09:25 PM
Who knows. Maybe. But if you want to not worry about it, put the new cap inside of the old cap/tube and put it back where you got it.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Website Find
morzh
Odobenus rosmarus
*****
Posts: 15,818
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
#3

04-22-2018, 11:02 PM
I don't see any problem with putying the new cap in the shield. In the 38-690 there were several, some in very inconvenient places, still I got them out and in after restuffing.
There likely was a reason behind it, it is safer to follow the old design rather than troubleshoot things later.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
LarryFS
Member
***
Posts: 120
Threads: 15
Joined: Aug 2017
City: Fort Worth State, Province, Country: TX
#4

04-23-2018, 09:03 AM
OK, thanks guys!  I will get the new one in there.

Larry
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently 7029 online users. [Complete List]
» 2 Member(s) | 7027 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration