Thread Rating:
  • 1 Vote(s) - 4 Average
  • 1
  • 2
  • 3
  • 4
  • 5

*Solved Minerva Tropic Master model w117 "early"-crackle pop & no vol ****SOLVED

I believe springy material on brake lines is to reduce vibration, lessens chance of a rub through. Older vehicles like my '69 Cobra Jet didn't use them, but my '72 Comet does have wrap on lines.

Tom

wiper to ground reads about 7 ohms this time, sometimes its 10, others is 2 and other times its like 20 but still low enough.

so... the ref gnd signal is stable enough to not be the fault for this.

it could be several things.

i tried calibrating down in resistivity of the 47kohm R after the wiper,, still have sound with vol at Min.

i think i will just live with it.

this bugger gets really HOT on the outside,,

headed out to put it back inside its carry case after i add my antenna relay back on.
i am considering a 120 v small fan to mount inside it....

new cooling fan in,,, now that really took care of the heat.


air intake is in the "back door"
air hits ceiling and goes left and right out the side louvers.


Attached Files Image(s)
       

i really want to add a couple things to this set

i want an S meter

i want a BFO even if its a gimick type.
i am getting a lot of side band in addtion to shortwave

i am going to start with the gimmick BFO type for side band if anyone has suggestions.

i know i will need another tuning cap which i have several.

from there i will need a knob on the tuning cap which i have.

i can string up and make a 0-100 scale which will be visible in the lower part of the main tuning window just below the words printed "tropic master".

how do i wire in such a thing?
do i attempt to copy cat the gimmick from my hallicrafters S38-d which actually works really great!.

any ideas or anyone experienced in doing this?

Hello friends, I loved seeing all the work in this rarity of 1944, I have a radio of this model here and I need to restore it, it is not as beautiful as this one on the topic, what was written in most components has worn out over time, I need to replace components mainly capacitors, I don't have his technical documentation, if any of your friends know of a site that I can download, please let me know, thank you very much !.

W-117 early version:

http://www.nostalgiaair.org/pagesbymodel...010877.pdf

W-117 late version:

http://www.nostalgiaair.org/pagesbymodel...010878.pdf

Better copies can be found here:

https://worldradiohistory.com/Archive-Ri...45-MNO.pdf

Good luck!

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
Hi Morzh, I've searched using Mondial as the user name with various keywords such as 'coupler', 'motor', 'idler', 'p...alangard — 08:31 PM
Philco 16B Parts
I think the chassis is painted.morzh — 08:13 PM
Philco 38-2 Automatic Tuning
Honestrly, the original is quite acceptable and, it seems to me, can be cleaned.morzh — 08:11 PM
Philco 41-608 changer coupler
Mondial left a thread about remanufacturing thois type coupler.morzh — 08:09 PM
IF can wire size and Rubber mounts?
Are you talking about rewinding or rewiring? For rewiring, meaning runnin wires to the coil from other components, the ...morzh — 08:08 PM
12' Philco
I wonder who would be able to "no stoop" with this one.morzh — 08:05 PM
IF can wire size and Rubber mounts?
Hello PHORUM members, I am still working on restoration of my PHILCO 37-640.  I want to start with rewiring the IF ca...georgetownjohn — 06:32 PM
Philco 41-608 changer coupler
I am working on a Philco 41-608 with the gear-driven changer.  The coupling (#35-2220) between the motor assembly and th...alangard — 06:29 PM
Gilfillan Brothers Car Radio?
There is a Mission Bell model 19/19A that could be what you’re looking for, Riders vol 4. It has the tube line-up of: 0Z...Joe Rossi — 05:01 PM
Looking for verification of correct schematic.
Definitely 870044RossH — 01:12 PM

[-]
Who's Online
There are currently 3734 online users. [Complete List]
» 1 Member(s) | 3733 Guest(s)
Avatar

>