Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

46-350 Repaired
#1

I am new to the Phorum and an electronics novice.  This afternoon I finished repairs on a 46-350 that I picked up at a junk shop on a recent trip to Ohio. The advice and tips I got on the Phorum made it possible for me to get this old portable working again. Thanks for the help. 
Wayne
#2

Welcome, Wayne.
Here goes #1. Icon_smile

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

Hi Wayne and welcome!
I'm a couple of miles south of the Willow Grove Mall so if you need anything look me up.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#4

Welcome to the Phorum! Icon_wave
#5

HAPPY TRAILS ,,,Mr. Wayne
#6

Terry: Glad to know that you are nearby. Let’s try to connect sometime soon. Wayne
#7

Check your pm bx.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#8

New to the Phorum, have a 46-350 that works, want to replace strap, not sure how the old one comes off, anyone here done this? I have replacement strap from someone who was selling them online, but hesitant to pry on stuff.

Thanks for any advice on this.

Long term, I want to build a battery box for the little radio, and do some minor clean up of the volume control and re-string the tuner string, the mechanism is pretty gunked up and needs a good clean up. I will post pics as I go along.
#9

Jan

Please start a new thread, this is someone else's plus it is a year old.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

[-]
Who's Online
There are currently 4938 online users. [Complete List]
» 2 Member(s) | 4936 Guest(s)
AvatarAvatar

>