Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

late 1936 116B Labeling
#1

Hello,
I am just finishing up the restoration on a late 1936 116B.  

   

Here is the cluster of inside case labels:

   


The labeling inside the cabinet contains a label that I had not encountered until this radio - the For Correct Operation label.    It is attached using one staple and is kind of "toasty" and aged.
   

It is 2" X 3 1/8" in size.  Just wondering on what other models this this label / tag used.  From the la
Thanks very much and stay well.
#2

My 116B didn't have much of any labels except or most of the tube layout. The rest lost to time...  How do you like your set?? I think mine is my favorite tabletop set. I do have a couple of 5 band 16B's in the works both needing major cabinet work. I'm curious how they compare to the 116B.


Attached Files Image(s)
   

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

Hi,
I am very impressed with this set.  My go-to set for shortwave entertainment has been my Scott All wave 23. The Philco 116 keeps pace with the Scott in bringing in distant stations.  I really like the two speed tuning knob on the Philco (even though it feels a bit rough - I got to revisit the tuning mechanism again).  The Scott only has single speed tuning.  All this pleasure and it still needs an alignment!  Can't wait till that is done.
So I must agree that the Philco 116B is my favorite table top and definitely one of my all-around favorite radios.




Users browsing this thread:
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4777 online users. [Complete List]
» 1 Member(s) | 4776 Guest(s)
Avatar

>