Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Puzzled -40-180
#1

What's happening here? The 6 meg tone control (51) is switched. That's why the dotted line. But the wiper can't be grounded, or the .01 cap, 40a, would just be shorted to ground. Why does the wiper have a circle for connection, instead of a dot? It appears the actual pot has nothing connector to the wiper.  How does this tone control work?

I'm confused.

[Image: https://i.imgur.com/e9jYt0n.jpg]
#2

It is correct.
The wiper simply brings GND closer to the C50,  cutting out the treble, or further away, letting the treble through.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

Got it. I'm getting old. I guess.
#4

Well I have a question too! where does the phase inversion come from for the push pull? Does it come from the screen grid of the upper 41, through the .01 cap #52?
#5

Yup...

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#6

This is called "Paraphase inverter".

It is described here.


https://dalmura.com.au/static/Phase%20In...201948.pdf


Look at Fig. 10.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#7

Thanks guys! I like the line "results are disappointing..." I would think there would be some phase problems between the 2 output tubes, but I've never played with the circuit.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
As far as I know, the Repairbench does not work, and has not been working in a while. Chuck (we had that campaign looki...morzh — 01:33 PM
Radio city products 664 schematic request
Need a schematic or manual for the 664. The 663 may be similar.daveone23 — 12:38 PM
New Philco Repair Bench
Thanks Gary.dconant — 12:16 PM
New Philco Repair Bench
I tried accessing the site through our library and got the same response. It's reported to our tech gurus. GaryGarySP — 11:50 AM
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM

[-]
Who's Online
There are currently 6808 online users. [Complete List]
» 1 Member(s) | 6807 Guest(s)
Avatar

>