1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
First Resto - Philco 60B
LDel
Junior Member
**
Posts: 21
Threads: 1
Joined: Feb 2021
City: La Baie State, Province, Country: Québec
#31

02-24-2021, 05:47 PM
Thank you - I'll look into this.
Find
LDel
Junior Member
**
Posts: 21
Threads: 1
Joined: Feb 2021
City: La Baie State, Province, Country: Québec
#32

03-06-2021, 04:46 PM
Success!!!!!  (Well, partial success.)  An AM transmitter arrived a few days ago.  It's hooked up to a computer and is broadcasting the music of Glenn Miller on the 60B.  

The tuning on the Philco is broad, and the dial is not calibrated correctly.  The AM transmitter is broadcasting at 1340, but the Philco is receiving at a frequency above the printed phenolic dial.  I just purchased a frequency counter, and I'll check to see how accurate my signal generator's scale is before I attempt to align the dial.  

This has been the most extensive repair/restoration that I have ever done.  It would have been, no doubt, a relatively simple matter for the more experienced members of the group.  I learned so much from the experience, and from the group.

I've always wanted a Philco ChairSide and a Philco 90.  If I can find reasonably priced ones, I will, no doubt, be back with more questions.

Again - Many, Many Thanks
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,295
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#33

03-06-2021, 05:52 PM
Glad to hear you got it percolating!

Have fun w/your "new" set.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 03-06-2021, 05:52 PM by Radioroslyn.)
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM
The list of my radio & TV collection!
Magical chords of forgotten melodies, old nostalgic music on an old radio... Saturday night blues on the Mid-Waves on an...RadioSvit — 12:20 PM
Philco 42-345 Restoration/Repair
Thank you MrFixr55 the issue with this radio is that the internal coil antenna is missing and there was a wire in its pl...osanders0311 — 11:34 AM

[-]
Who's Online
There are currently 2608 online users. [Complete List]
» 1 Member(s) | 2607 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration