1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 87 cap block
Micro9
Junior Member
**
Posts: 36
Threads: 15
Joined: Aug 2007
City: Glendale,AZ
#1

02-28-2010, 10:57 PM
Are the 2.0 and 1.0UF caps in the cap block e-caps or reg caps....Also the neutralizing caps 7,12,and 17
have the wax out on one and need to be replaced...the schematic show those as a 100 ohm resistor and
a .1 cap as a unit...can i use a .1 cap and parallel a 100 ohm resistor across it for the same results?...OOPS..
the neutralizing caps 7,12,and 17 should be BY-Pass caps!!!!!
Thanks in advance...
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

03-01-2010, 09:25 PM
The 1 & 2 mfd caps where originally paper but you can use either for replacement purposes. Go with 600v jobs. Usually neutralizing caps are small variable caps not fixed value paper ones. The bypass caps go from B+ to ground the resistors are in series with the B+. If you connect them in parallel with the bypass you will short the B+ to ground. Not a good thing.
Terry
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM
Philco Predicta Siesta picture over time getting dimmer
I found that the wire insulation was burnt.  The fly back needs corona dope! Why would someone put that there?Platinumblonde36 — 01:09 AM
Philco Predicta Siesta picture over time getting dimmer
This is what it looked like beforePlatinumblonde36 — 01:01 AM
Philco Predicta Siesta picture over time getting dimmer
Platinumblonde36 — 12:58 AM
Philco Predicta Siesta picture over time getting dimmer
Platinumblonde36 — 12:57 AM
Philco Predicta Siesta picture over time getting dimmer
I'm finding some strange things in my set and for the most part it's also original, so I need to start going over everyt...Platinumblonde36 — 12:55 AM
12' Philco
Not anymore Mike. Andre The Giant Born: May 19, 1946, Coulommiers, France Died: Jan 28, 1993 (46 years), Paris, Fran...RodB — 11:53 PM
IF can wire size and Rubber mounts?
Renovated Radios do carry what you need. As for the voltage, a wire should be at least 300V-rated.morzh — 11:13 PM

[-]
Who's Online
There are currently 4084 online users. [Complete List]
» 1 Member(s) | 4083 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration