Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

1935 Atwater Kent Model 456 on Youtube
#1

Hello Phorum
I have a new series on an Atwater Kent Model 456.
Part 1 link below to anyone interested
https://youtu.be/n3ar_HLBw4c
#2

That's a project! I'm looking forward to more installments. I'm also enjoy those old 8mm films you've been sharing.

Thanks for doing the videos Buzz!

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#3

Thanks Buzz !

I don't hold with furniture that talks.
#4

Hello All:
Part 2 of this series is now uploaded
link below to anyone interested.
https://youtu.be/bhKyRA-gq4U
#5

Part 3 is now uploaded. Link below to anyone interested

https://www.youtube.com/watch?v=wIYJmCer...l=Buzz1151
#6

Hi Buzz ! That was very interesting, but I'd say you still have a way to go. That set should be WAY more sensitive than that, even with a fairly short antenna. Of course, I didn't see you do any alignment on the video, so, that will probably help. I'll look forward to Part 4.
#7

It's coming along nicely Buzz, that new dial looks great. Enjoy that premium whiskey, Dickel is so generous Icon_e_wink

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#8

Part 4 and FINAL episode is now uploaded.
link below to anyone interested.
https://youtu.be/dE7ceYBjdeE




Users browsing this thread:
[-]
Recent Posts
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM
Philco 38-7 Speaker
7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM

[-]
Who's Online
There are currently 2988 online users. [Complete List]
» 2 Member(s) | 2986 Guest(s)
AvatarAvatar

>