Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

16B cabinet color
#1

The house of a recently deceased neighbor is being cleaned out and this kinda tired 16B was headed for the dumpster. I thought
I'd see what I could do with it and, with the amount of labor involved, I might as well do it right-  so here's my question: What
color were the dark parts of the cabinet, black or very dark brown? Was the finish meant to be opaque or was the grain meant
to show through? The cabinet was stripped long before I got it.
  One idle curiosity question too. I'm not used to seeing eight-sided knobs on Philco products. How long were they used and did
the whole product line get them or just some models?
   Sorry for asking questions you guys probably settled long ago.
-Dave


Attached Files Image(s)
   
#2

Hi Dave - a previous post on the colors for these cabinets: https://philcoradio.com/phorum/showthread.php?tid=8830
#3

Here's the link to our gallery photo as well:
https://philcoradio.com/gallery2/1935a/#Model_16B
#4

Hi Dave and welcome to the Phorum,

You found one of Philco's best table top sets. It's a beast! I have a couple of the them.
Here's a link to the 1st cabinet I did. https://philcoradio.com/phorum/showthread.php?tid=19986
It was stripped too. And broken. I ended up using
Mohawk Van Dyke Walnut M100-0353. I don't think it's as red as the extra dark walnut.
Also used a lot of sanding sealer. The hypo work wonders for doing the pinstriping.

I'll mention while your working on the cabinet be sure to check the joints. Loose joints
can cause splitting and cracking of the corner and top panels as it's a heavy set to pick
up by the rear arch.

As for the knobs I can't think of many sets that use them. Would have been around 1934
-35. Renovated Radios was making repos for all 3 of them.  And the grille cloth can be had
from Micheal Katz.

GL w/your new project!

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#5

Hello Dave and welcome to the Phorum! Terry wasn't kidding when he said "beast". Make sure the table you put it on is sturdy as well! The others showed you where to start, so I'll just say Good Luck! Take care and BE HEALTHY! Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
An attempt to remove the Field Coil from a G speaker
Arran The oxidation seems to go deep, a few layers. The break starts right there, but then it will occur on every la...morzh — 07:35 PM
An attempt to remove the Field Coil from a G speaker
Mike, This is just a thought, the are on the coil where the verdigris (green oxidation is) I wonder if that is where ...Arran — 06:32 PM
An attempt to remove the Field Coil from a G speaker
Mike; I've made a one or two spiders by using some card stock, and a razor blade, it took more then one try but they ...Arran — 05:48 PM
Philco 91 Restore Code ??
I wondered about that. Wish there was some place local to get this stuff.dconant — 04:20 PM
Philco 89 indicator light.
Bending the lamp bracket (moving the lamp, that is) can possibly change the shape of the pointer a bit, but not its loca...morzh — 04:01 PM
Philco 91 Restore Code ??
Because the usable power rating of it then is (3,200/20,000)*25W= 4W. Maybe a tad more due to the mass, but not much. Yo...morzh — 03:59 PM
Philco 89 indicator light.
Thank you Dan, that was the trick. I kept trying to rebend the lamp bracket but that wasn't doing anything to help.Jim Dutridge — 02:18 PM
Philco 91 Restore Code ??
20K 25 watt. I thought it was a 20 watt at first.dconant — 01:37 PM
My Philco 37-116 Restore
Nah, too much and not that important.morzh — 01:33 PM
Philco 91 Restore Code ??
What's the full value of that resistor?morzh — 01:31 PM

[-]
Who's Online
There are currently no members online.

>