1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco Model 90 volume pot value
WyTex
Senior Member
****
Posts: 289
Threads: 42
Joined: Jan 2014
City: Jeffersonville State, Province, Country: PA
#1

03-08-2023, 08:38 PM
Hey fellas - 

Continuing a battle with a Model 90 w/single 47 tube version.  There's audible audio when turned all the way down plus some strange crackling after 10-15 minutes of use.   Volume pot part #5366 does not list a value and haven't been able to locate it.  I'm suspecting this one might be bad and have a spare.  The current pot measures 676k while the spare measures 215k.  

Thanks,
Paul
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa
#2

03-08-2023, 11:39 PM
1/2 meg.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
radiorich
Phorum Expert
*****
Posts: 1,472
Threads: 89
Joined: May 2008
City: Omak State, Province, Country: WA
#3

03-09-2023, 09:04 AM
Hello Paul,
One thing I would check is disconnect that volume control and hook an meter on it to
check how smooth the volume resistance changes and if you have one an old analog meter like my Simpson 260 works well for this !

Sincerely Richard
Find
WyTex
Senior Member
****
Posts: 289
Threads: 42
Joined: Jan 2014
City: Jeffersonville State, Province, Country: PA
#4

03-09-2023, 12:52 PM
Thank you Terry and Richard.  I also happen to have a Simpson 260 and will test.

Paul
Find
« Next Oldest | Next Newest »




Users browsing this thread:
[-]
Recent Posts
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM
Philco 38-7 Speaker
7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM

[-]
Who's Online
There are currently 2463 online users. [Complete List]
» 2 Member(s) | 2461 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration