1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Coronado 962A
RodB
Phorum Expert
*****
Posts: 986
Threads: 40
Joined: Feb 2015
City: Roseville, MN
#1

07-17-2024, 11:25 AM
I'm looking at replacing an output transformer for this farm radio. It has 2 1Q5s in parallel driving a SE OPT. The 1Q5 has a suggested plate load of 8k. If the tubes are in parallel then can I be okay using an OPT with a 4K primary impedance?
(This post was last modified: 07-17-2024, 12:44 PM by RodB.)
Find
Arran
Phorum Expert
*****
Posts: 4,702
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#2

07-17-2024, 05:10 PM
Just out of curiosity is there an economy switch that shuts off one of the 1Q5 tubes to save on battery life? I couldn't find a 962A on N.A only a 962 so I assume it's similar. I think you would be right about the plate load impedance being 4000 Ohms, but I'm sure someone else will chime in.
Regards
Arran
Find
RodB
Phorum Expert
*****
Posts: 986
Threads: 40
Joined: Feb 2015
City: Roseville, MN
#3

07-17-2024, 05:20 PM
There doesn't seem to be a switch to turn off one of the 1Q5s. The schematic at NA is the correct one. The A suffix is for speaker size as noted in the schematic.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Looking for verification of correct schematic.
Klondike98, Thank you. I'll double check that SN and get back to you. GarySP, Thank you for the schematic.RossH — 12:13 AM
Looking for verification of correct schematic.
I think you have the correct take on your set. Ron's annotated early schematics that note the below B22000 serial numbe...klondike98 — 12:04 AM
Looking for verification of correct schematic.
Hello Ross. The Philco Radio Library located at the bottom of the page has the schematic with the tube count you have. ...GarySP — 10:48 PM
HiFi (Chifi) tube amp build - but my own design.
Tim It's be interesting if you put your schematic here. Who knows, you could get some advice from a few folks here. ...morzh — 10:01 PM
Philco 42-390, code 121 speaker
Thanks for that information. It would appear from the output transformer parts list that the transformer that was origi...Stevelog — 07:21 PM
Looking for verification of correct schematic.
I would like to verify that my thoughts are correct regarding my Model 70 and its appropriate schematic. My chassis inf...RossH — 06:26 PM
Philco 42-390, code 121 speaker
Welcome to the Phorum, Steve! The Philco Radio Library located at the bottom of the page has info on speakers and outpu...GarySP — 06:24 PM
Philco 42-390, code 121 speaker
I recently became the owner of a Philco console 42-390, saving it from the dumpster.  It is missing the speaker. It uses...Stevelog — 12:07 PM
Help identifying
Thanks for the welcome, Gary. There exists only one photo of the unit in the Richard Neutra-designed home. The photo (th...Davino — 10:54 AM
Help identifying
Welcome to the Phorum, Davino! Not much to go on from the above pictures. Would it be possible to take a photo or two ...GarySP — 10:25 AM

[-]
Who's Online
There are currently 1204 online users. [Complete List]
» 1 Member(s) | 1203 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)