Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

45F - What to do?
#1

Hi - I just picked up a Philco 45F for $25 at an estate sale. I plugged it in, powered it on -I don't have a variac, unfortunately - and the tubes glowed, but all I got was some hum/buzz from the speaker.

However, I did get some crackling when turning the volume knob so I thought I'd ask: is there any place that I can alligator-clip the leads from a CD player or something to see if I can get some sound?

I am a studio engineer, and more recently, a neophyte vintage-audio enthusiast. I've done some tech-work before, but nothing too serious, and I've never worked on a radio. However, I do know enough to be careful around these old tube-amps, so I thought I'd seek some advice before poking around the chassis.

Cheers,

C.Burnett
#2

A straightforward method would be connect directly across the terminals of the volume control. Richard
#3

Hello and welcome!

Unfortunately, you will have hum until you replace the set's electrolytic capacitors. This is their way of screaming "Help! We're dying...and if you don't replace us soon, we will short out, killing the power transformer too!"

http://www.philcoradio.com/tech/plugin.htm
http://www.antiqueradio.org/powerup.htm

You can hook up a CD player as Richard suggested...but it will still hum until you replace the electrolytics.

If you plan to operate the radio, you need to replace not only the electrolytics, but all of the set's paper capacitors as well for reliability and safety.

--
Ron Ramirez
Ferdinand IN
#4

Thanks very much for the info - accurate on all counts. I clipped across the volume pot and got about halfway through a Sinatra/Dorsey album when one of the electrolytics busted and sent out a jet of...whatever's in an electrolytic capacitor. I really like this radio, though, and I think I'll take it in to my tech for a re-cap.

C.B.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone,  Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM

[-]
Who's Online
There are currently 3893 online users. [Complete List]
» 1 Member(s) | 3892 Guest(s)
Avatar

>