Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

37-116 2 different grill cloths?
#1

Working on a 37-116 and I noticed that it had a different pattern of cloth behind the small cutouts. The cloth all looks old and I'm wondering if this is an old repair or was it made this way?

Note from site admin: Sorry, but the photo which was attached to this post is no longer available.

John
Las Vegas, NV USA
#2

It's an old repair, because neither pattern is correct.

It should have the 1935-37 "V" pattern cloth in all three openings:
[Image: http://i326.photobucket.com/albums/k420/..._cloth.jpg]

Of course, now that this pattern is no longer being reproduced, unless/until someone else begins to reproduce the cloth again, we have to make do as best we can, just like we did before reproduction grille cloth became available.

--
Ron Ramirez
Ferdinand IN
#3

I knew I should have bought more of the V pattern when it was available. My 116 will have to wait now. Icon_sad

Steve Chambers
#4

I think I'm gonna cry. A 5' by 7'8" hunk of the cloth went on ebay last month for $260.50

http://cgi.ebay.com/280742240172

Icon_cry Icon_cry Icon_cry Icon_cry Icon_cry

John
Las Vegas, NV USA
#5

Lets not get nuts about cloth. As long as it is somewhat acousically tansparent and hue and value somewhat match the cabinet you have done well.
#6

That cloth looks like it came from an RCA radio, not correct but it doesn't look bad. I wouldn't panic about the grille cloth, it will go back into production eventually and then the party that paid $260 for a bolt of the Philco chevron cloth will be kicking themselves.
Regards
Arran




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently no members online.

>