Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Volume Control Cleaning Tool
#1

Some while ago I ran across a web site where an apparently older gentleman sold some pretty nifty aids and tools. I do remember he had a tool that apparently screwed onto the volume control shaft, allowing you to force cleaner into the sealed volume control to clean it. I remember trying to order it, sent a money order only to get it back, where he stated he needed to fabricate some more and was out at the time.

Anyone know who this fellow may be and how to get in touch with him?

One other quick one... Anyone seen or used the chassis tool that you place on your bench top allowing you to more easily work on some of those hard to get to chassis?

Thanks for your replies!
David
#2

Was it Bill Turner? He has such a device listed on his website:

http://www.dialcover.com/components.html

I know Bill has had health problems in the past few years.

Sean
WØKPX
#3

Sean,

I just read your post, got excited and used the email link on Bill's website. My email immediately came back stating that the email box for Bill was full and my email couldn't be delivered. I suspect that he's quite ill as you state and unable to carry his hobby on as he'd like. Hope he's better soon.

Anyone know of anyone else that has a product(s) like his?

Thanks so much!
David
#4

dnitram Wrote:............. My email immediately came back stating that the email box for Bill was full and my email couldn't be delivered........
That's because Bill used some kind of odd e-mail (T.V. based?) and when that service went defunct he never adapted. You either have to call or just send in your order to Bill.

I sent in an order a year or so ago and it seems I read where others also got their orders from Bill recently.

Note the following message taken from his site (homepage):
Quote:Feel free to contact me via telephone for additional information. Email is not available at this time. Orders may be placed in writing with payment enclosed via mail to:
BILL TURNER
1117 PIKE ST.
ST. CHARLES, MO 63301

Tel: (636) 949-2210

CASH, CHECK or MONEY ORDER ACCEPTED
Sorry, no PayPal or credit cards

http://www.dialcover.com/home.html

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#5

Just checked for postings by Bill over on ARF, and it's been a year since he has posted there.

Carl
Northern Panhandle, WV




Users browsing this thread:
[-]
Recent Posts
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM
The list of my radio & TV collection!
Magical chords of forgotten melodies, old nostalgic music on an old radio... Saturday night blues on the Mid-Waves on an...RadioSvit — 12:20 PM
Philco 42-345 Restoration/Repair
Thank you MrFixr55 the issue with this radio is that the internal coil antenna is missing and there was a wire in its pl...osanders0311 — 11:34 AM
Philco 610B oscillator wiring
Regarding the oscillator circuit which is comprised of the 6A7's cathode, control grid, and screen grid. These elements ...Radioroslyn — 10:33 AM
Philco 42-345 Restoration/Repair
Hi OSanders, First off, welcome to the Philco Phorum where Phine Phamily-Phriendly Pholks Phull of Philco Phacts and P...MrFixr55 — 08:41 AM
Philco 42-345 Restoration/Repair
Today I've been reading through the site trying to learn more about this radio. I also soldered the lose power cord cabl...osanders0311 — 08:24 PM

[-]
Who's Online
There are currently 2396 online users. [Complete List]
» 1 Member(s) | 2395 Guest(s)
Avatar

>